Ikelite 1-Inch Auxiliary Ball Mount Mark II
$ 34.95
Ikelite 1-Inch Auxiliary Ball Mount Mark II - 408171
Mounts to the Auxiliary Ball Clamp for the attachment of additional lightweight accessories in the middle of your strobe arm. Requires the Auxiliary Ball Clamp, sold separately.
Â
Â
Ikelite 1-Inch Ball Arm Extension Mark II 12-Inch Length
$ 64.95 - Sold Out
Ikelite 1-Inch Ball Arm Extension Mark II 12-Inch Length - 408112
A rigid anodized aluminum arm with balls at each end to extend your strobe or video light arm. Add an extension and clamp to your existing strobe arm for reduced backscatter and more creative lighting effects when shooting with a wide angle lens.
The slotted design allows for the attachment of a lightweight accessory in the middle of the extension. When used with our Sliding Ball Mount, the additional accessory is able to move up and down the length of the arm for quick repositioning during a dive.
Ikelite 1-Inch Ball Arm Extension Mark II 5-Inch Length
$ 49.95 - Sold Out
Ikelite 1-Inch Ball Arm Extension Mark II 5-Inch Length - 408105
A rigid anodized aluminum arm with balls at each end to extend your strobe or video light arm. Add an extension and clamp to your existing strobe arm for reduced backscatter and more creative lighting effects when shooting with a wide angle lens.
The slotted design allows for the attachment of a lightweight accessory in the middle of the extension. When used with our Sliding Ball Mount, the additional accessory is able to move up and down the length of the arm for quick repositioning during a dive.
Ikelite 1-Inch Ball Arm Extension Mark II 7-Inch Length
$ 49.95
Ikelite 1-Inch Ball Arm Extension Mark II 7-Inch Length - 408107
A rigid anodized aluminum arm with balls at each end to extend your strobe or video light arm. Add an extension and clamp to your existing strobe arm for reduced backscatter and more creative lighting effects when shooting with a wide angle lens.
The slotted design allows for the attachment of a lightweight accessory in the middle of the extension. When used with our Sliding Ball Mount, the additional accessory is able to move up and down the length of the arm for quick repositioning during a dive.
Â
Â
Ikelite 1-inch Ball Clamp Mark II for Lightweight Accessories
$ 34.95 - Sold Out
Ikelite 1-inch Ball Clamp Mark II for Lightweight Accessories - 408121
The Accessory Clamp attaches two (2) 1-inch diameter balls. In travel, every ounce counts so we reduced plate thickness and chose a light, three prong wing nut to reduce weight as compared to our Standard Clamp. The result is a lighter, maneuverable clamp with the perfect amount of holding power for small lights and accessories which weigh less than one pound. Plates are spring-loaded for easy assembly and breakdown of your arm system.
Ikelite 1-inch Ball Clamp Mark II with Auxiliary Mount
$ 49.95 - Sold Out
Ikelite 1-inch Ball Clamp Mark II with Auxiliary Mount - 408122
The Accessory Clamp attaches two (2) 1-inch diameter balls. The base plate accepts the Ikelite Auxiliary Ball Mount for the attachment of additional lightweight accessories in the middle of your strobe arm. Perfect for adding a spare modeling light or video light.
Plates are spring-loaded for easy assembly and breakdown of your arm system.
Â
Â
Ikelite 1-Inch Ball Mount for GoPro
$ 34.95
Ikelite 1-Inch Ball Mount for GoPro - 408173
Mounts to GoPro cameras for attachment to 1-inch diameter ball arms from Ikelite, TLC, Ultralight, Nauticam, and others. Requires a compatible 1-inch Ball Clamp, sold separately.
Ikelite 1-Inch Ball Mount for Steady Tray for GoPro
$ 29.95
Ikelite 1-Inch Ball Mount for Steady Tray for GoPro - 408174
Ikelite 1-inch Ball Mount for Studio Light Stands
$ 34.95
Ikelite 1-inch Ball Mount for Studio Light Stands
Ikelite SKU: 4081.75 | Helix SKU: 408175
Overview
Attach your Ikelite DS strobe to almost any light stand for studio photography. A 1-inch diameter ball mount with o-ring is compatible with the Ikelite ball arm system and most ball arm systems from Ultralight, Nauticam, TLC, and other manufacturers. Clamp and light mount sold separately.
The ever-growing selection of lighting accessories on the market demands a mounting system that's highly expandable, flexible, and streamlined. In answer to this need, the second generation of our 1-inch ball arm system provides improved ergonomics and versatility in a lighter, sleeker package. Possible combinations are virtually endless, with opportunities to mount an additional lightweight accessory almost anywhere along the length of an arm.
The 1-inch Ball Arm System Mark II features 1-inch ball components with a groove and o-ring to prevent slippage for improved holding power with less force. While underwater, clamps may be finger-tightened to keep lighting in place yet allow repositioning without loosening the clamp.
All parts are hard coat type III anodized for a long lasting, scratch resistant finish.
Compatibility
Works with 1-inch ball arms from Ikelite, TLC, Ultralight, Nauticam, and others.
Old and new Ikelite 1-inch balls and clamps are interchangeable. For the best performance, we recommend combining like components within a single clamp (two balls with grooves, or two balls without grooves). Ball components with an o-ring groove should have an o-ring installed at all times.
Specifications
1" (25.4mm) diameter ball
Type III hard coat anodized aluminum
0.8 oz (23g)
1" D x 2.6" L (25x66mm)
Ikelite 1-Inch Ball Mount Mark II for DS51, DS125, DS160, DS161 Strobes
$ 24.95
Ikelite 1-Inch Ball Mount Mark II for DS51, DS125, DS160, DS161 Strobes - 40814
Mounts to DS50, DS51, DS125, DS160 or DS161 strobes for attachment to 1-inch diameter ball arms from Ikelite, TLC, Ultralight, Nauticam, and others. Requires a compatible 1-inch Ball Clamp, sold separately.
Ikelite 1-Inch Ball Mount Mark II for DSLR Top Mount
$ 24.95
Ikelite 1-Inch Ball Mount Mark II for DSLR Top Mount - 40816
Mounts to the top of an Ikelite DSLR featuring 1/4-20 top mount for attachment to 1 in diameter ball arms from Ikelite, TLC, Ultralight, Nauticam and others. Requires a compatible 1-inch Ball Clamp, sold separately.
Ikelite 1-Inch Ball Mount Mark II for Quick Release Handle
$ 50.00
Ikelite 1-Inch Ball Mount Mark II for Quick Release Handle - 408131
Mounts to our Quick Release Handle for attachment of 1-inch diameter ball arms from Ikelite, TLC, Ultralight, Nauticam, and others. Requires a compatible 1-inch Ball Clamp, sold separately.
Ikelite 1-Inch Ball Mount Mark II for Vega
$ 24.95
Ikelite 1-Inch Ball Mount Mark II for Vega - 40815
Mounts to the Vega Video + Photo Light for attachment to 1-inch diameter ball arms from Ikelite, TLC, Ultralight, Nauticam, and others. Requires a compatible 1-inch Ball Clamp, sold separately.
Ikelite 1-inch Ball with Extended Sensor Mount Mark II for Quick Release Handle
$ 50.00
Ikelite 1-inch Ball with Extended Sensor Mount Mark II for Quick Release Handle - 40813
Mounts to our Quick Release Handle for attachment of 1-inch diameter ball arms from Ikelite, TLC, Ultralight, Nauticam, and others. Requires a compatible 1-inch Ball Clamp, sold separately. Extended length allows for the attachment of the EV Manual Controller.
Ikelite 1-Inch Sliding Ball Mount Mark II
$ 34.95
Ikelite 1-Inch Sliding Ball Mount Mark II - 408172
Mounts to Ball Arm Mark II Extensions for the addition of a lightweight accessory in the middle of your arm system. A three-pronged wing nut provides adjustability to slide your accessory up and down the length of the arm to reposition lighting easily during your dive. Requires a Ball Arm Mark II Extension, sold separately.
Ikelite 1-inch Standard Ball Clamp Mark II
$ 44.95 - Sold Out
Ikelite 1-inch Standard Ball Clamp Mark II - 40812
The Standard Clamp attaches two (2) 1-inch diameter balls. Thicker plates provide the perfect combination of strength and range of motion. Plates are spring-loaded for easy assembly and breakdown of your arm system. A hard anodized aluminum wing nut allows for easy one-handed operation and will withstand years of use.
Ikelite 1-inch Triple Ball Clamp Mark II
$ 59.95 - Sold Out
Ikelite 1-inch Triple Ball Clamp Mark II - 408123
The Triple Clamp attaches three (3) 1-inch diameter balls. Use in place of any Standard Clamp to double your mounting options. Plates are spring-loaded for easy assembly and breakdown of your arm system.
Â
Â
Ikelite 1.25in Ball Arm 9in Length
$ 30.00 - Sold Out
Ikelite 1.25in Ball Arm 9in Length - 958009
Ikelite Product Number 9580.09
Â
Â
Â
Ikelite 1.25in Ball Extension 6in Length
$ 50.00
Ikelite 1.25in Ball Extension 6in Length - 046806
A rigid anodized aluminum arm with balls at each end to extend your strobe arm. Requires compatible clamp at each end. Add an extension and clamp to your existing strobe arm for reduced backscatter and more creative lighting effects when shooting with a wide angle lens. 6 in (15 cm) extension with 1.25 in (3.2 cm) diameter balls at each end.
Â
Â
Ikelite 1.25in Ball Extension 9in Length
$ 60.00
Ikelite 1.25in Ball Extension 9in Length - 046809
A rigid anodized aluminum arm with balls at each end to extend your strobe arm. Requires compatible clamp at each end. Add an extension and clamp to your existing strobe arm for reduced backscatter and more creative lighting effects when shooting with a wide angle lens. 9 in (22 cm) extension with 1.25 in (3.2 cm) diameter balls at each end.
Â
Â
Ikelite 1.25in Ball with Dovetail Mount
$ 30.00
Ikelite 1.25in Ball with Dovetail Mount - 95777
Requires a compatible Clamp for 1.25 in Balls, sold separately.
Â
Â
Ikelite 1.25in Ball with Nikonos Shoe Mount
$ 30.00
Ikelite 1.25in Ball with Nikonos Shoe Mount - 95776
Mounts to a Nikonos IV or V shoe. Requires a compatible Clamp for 1.25 in Balls, sold separately.
Â
Â
Ikelite 1.25in Ball with Tray Mount
$ 30.00
Ikelite 1.25in Ball with Tray Mount - 95771
Mounts to Ikelite handles featuring a 3/8 in bolt and wing nut. Requires a compatible Clamp for 1.25 in Balls, sold separately.
Ikelite 1.25in Ball with Universal T Mount
$ 30.00
Ikelite 1.25in Ball with Universal T Mount - 95775
Requires a compatible Clamp for 1.25 in Balls, sold separately.
Â
Â
Ikelite 15' TTL Extension Cord
$ 99.95 - Sold Out
Ikelite 15' Sync Cord Extention - 410215
Non-coiled 15 ft (4.5 m) long extension cord with Ikelite-style bulkhead on one end and Ikelite-style strobe plug on the other end. Use to position your strobe in a location farther from your housing than accommodated by a normal coiled cord.
Communicates TTL signal when used with compatible strobe, housing and sync cord. The Ikelite-style bulkhead and plug are widely recognized as the most reliable waterproof strobe sync connections available. Built-in strain reliefs reduce stress on cord ends.
Ikelite 200DL Underwater Housing for Canon EOS 6D DSLR Cameras
$ 1,695.00
Ikelite 200DL Underwater Housing for Canon EOS 6D DSLR Cameras
Ikelite SKU: 71706 | Helix SKU: 71706
Overview
A full featured and durable waterproof housing for Canon EOS 6D DSLR cameras. Suitable for scuba, snorkel, surf, pool, and any application in or around the water.
This housing requires the addition of a compatible DL Lens Port for waterproof operation. Lens Port not included.
Lens Ports
This housing features our robust new Dry Lock (DL) port system. "Dry Lock" refers to the placement of the o-ring on the outside of the port mount. This improves visibility and reduces the chances of water dropping onto your precious camera sensor. DL ports are the lightest on the market, yet robust and capable of standing up to rough surf. Attachment is quick and secure. A system of extensions can accommodate a huge variety of lenses with ease.
Most popular zoom lenses and select lens focus rings can be engaged using a simple yet effective gearing system that puts adjustment right at your fingertips. A large, soft-touch lobed knob on the side of the housing makes fine tuned adjustments a breeze. Zoom and focus gears differ depending on which lens you are using. All are lightweight and affordable. Refer to the DL System Port Chart to choose the correct gear. Zoom gears sold separately.
Legacy Four Lock Port Compatibility
Due to differences in mount diameter and zoom engagement, DL and FL system ports cannot be used interchangeably. The DL port mount may be removed using a T15 Torx bit and replaced with old style Port Locks for FL Port System (Set of 4) # 5509.04 for legacy users with standard or modular ports from our Four Lock system. This modification will prevent the use of newer DL ports. Re-installation of the DL port base will require the housing to be returned to Ikelite or an Authorized Dealer and may incur additional service charges. The housing cannot be converted back and forth repeatedly. There are significant advantages to upgrading your lens ports which you can read about here. If you're shooting an 8" diameter dome, you'll also save almost 2 pounds by switching to the DL version.
Vacuum System
The included vacuum valve allows you to pressurize the housing to check for leaks prior to putting your expensive equipment in the water. Use of the vacuum valve requires a compatible Vacuum Pump with Gauge # 47011, sold separately.
There is no greater assurance than being able to see your camera and o-ring seal through the back of the housing. Our signature open-groove design suspends the rear o-ring in a natural position that is easier to maintain and more reliable than forcing the o-ring into a channel. Once the housing is closed you can see the o-ring form a solid, waterproof seal.
TTL Exposure
This housings supports your choice of shooting manual strobes or adding TTL electronics depending on your application. Our new modular electronics system allows the housing to be updated with future strobe communications products as they become available. The flash bulkhead has been moved to the top of the case for improved cord routing and reduced strain. Reliable locking connectors between the hotshoe and bulkhead make it easy to install the optional TTL electronics or carry back up parts when traveling to remote locations.
You can enjoy the fastest and most accurate TTL exposure on the market by adding the CT1K Canon TTL Kit # 46070 and a compatible Ikelite DS strobe. Exposure compensation can be used added or subtracted in the camera.
Controls and Set-Up
Shutter and AF-ON levers stand out with super sensitive and natural feeling curved levers. Both controls can be extended using the optional Shutter Trigger Extension # 4077.93 for more comfortable use when using a right-hand quick release handle.
All push button controls are machined and hard anodized aluminum to reduce weight and resist salt build-up. The back of the housing is laser engraved with control symbols which will never fade or fall off.
The camera mount is front-loading for easy installation and removal. A small mounting plate attaches to the bottom of the camera and secures in the front of the housing. The camera mounting plate does not need to be removed from the camera for surface use or when changing the battery or memory cards. The mounting plate features a 1/4-20 threaded mount on the bottom so that it can be attached to a tripod on the surface.
Viewfinders
The included Super-Eye Viewfinder provides an enhanced view of the camera's optical viewfinder when viewed through a dive mask. The viewfinder removes quickly and easily for the attachment of an optional Straight Magnified Viewfinder # 6890 or 45° Magnified Viewfinder (Type 2) # 6891.2. The angle of a 45º viewfinder is more ergonomic when shooting underwater plus it provides a larger and brighter view than the standard Super-Eye.
Handling & Travel
The housing, tray, and handles have been optimized to reduce weight while maintaining strength and durability. The Right-Hand Quick Release Handle # 4077.02 (sold separately) can be added or removed depending on your needs. The precision machined aluminum base features 1/4-20 tripod mounting sockets and additional mounting locations for future accessories. The base and handle can be quickly removed when breaking down your system for travel.
A 1/4-20 threaded mounting point is located front and center on the housing above the lens port mount. This mount can be used to attach lightweight accessories like a focus light or GoPro camera.
If you're shooting with two strobe or lighting arms, then a top handle can be added to carry to and from the dive site. Top handles are available in a Cable Grip # 4080.07 or Aluminum Top Handle # 4080.08. The rigid aluminum version provides additional mounting points for lighting and accessories.
Construction
Our new ABS-PC blend front is stronger than its clear counterpart, provides improved contrast and visibility, and keeps your camera running cooler in the sun.
Every housing is made in the USA, individually inspected for fit, and water pressure tested to 200 feet (60m).
Non-Ikelite Strobes
SEA&SEA, INON, and Retra strobes with an electrical connection can be triggered in manual exposure modes using an electrical sync cord. Strobes without an electrical sync cord connection cannot be attached to this system unless slaved off of a hard-wired strobe.
Ikelite Non-Digital Strobes
Older non-digital strobes featuring an ICS-5 electrical sync cord bulkhead can be used with this system in manual exposure modes.
Fiber Optic
Fiber optic only strobes are not compatible with this installation. An external strobe must be connected by electrical sync cord.
Remote Triggering
Strobes with remote slave capabilities may be triggered off of a flash attached to the housing by electrical sync cord. Ikelite DS strobes support remote triggering using the Optical Slave Converter # 4403 or the Water Wizard system (manufactured and sold by Aquatica).
Compatibility
This housing is only compatible with Canon EOSÂ 6D camera as shipped by the manufacturer. Unless otherwise noted, this housing does not accommodate the use of add-on grips, battery grips, eyepieces, LCD covers, or other accessories.Â
Differences in lens and control placement prevent other DSLR models, including the newer EOS 6D Mark II, from being used in this housing. We are not aware of any other models which may be used in or adapted to this particular housing.
Specifications
200' (60m) depth rating
Compatible with DL system lens ports
Controls are provided for all important camera controls; Controls are not provided for LCD panel illumination button, Depth-of-field preview button, Dioptric adjustment knob, Multi function lock switchÂ
1/4-20 thread base mounts with 3.5" spacing
Near neutral buoyancy in fresh water
Actual buoyancy varies depending on choice of lens and port
4.8 lb (2.2 kg)
9.2 x 7.1 x 6.6" (234 x 180 x 168 mm)
Vacuum valve included (pump sold separately)
Included Ikelite ICS-5 bulkhead connector with manual hotshoe for reliable electrical triggering of underwater strobes; Optional TTL accessories provides automatic exposure with compatible Ikelite DS strobes
ABS-PC construction is fundamentally corrosion-resistant
Made in the USA; Individually inspected for fit and water pressure tested to depth
1 year limited warranty
What's in the Box
Housing
Rear O-ring # 0132.59 (installed)
Front O-ring # 0132.45 (installed)
Base with Left-Hand Quick Release Handle # 4077.67
Port Hole Cover # 0200.92 (installed)
Waterproof Bulkhead Cap # 9104.5Â (installed)
Zoom Gear Retainer # 75900 (installed)
Tool for Zoom Gear Retainer # 0945.06
4-40 Hex Key # 0945.11
1/16" Hex Key # 0945.16
1/8" Hex Key # 0945.18
Control + Push Button Tip Assortment # 9249
Silicone Lubricant 2cc Tube # 0184.2
ikelite 200DL Underwater Housing for Fujifilm X-T4 Mirrorless Digital Camera
$ 1,695.00
ikelite 200DL Underwater Housing for Fujifilm X-T4 Mirrorless Digital Camera
ikelite SKU:Â 71504 | Helix SKU: IK71504
Overview
Â
A full featured and durable waterproof housing for Fujifilm X-T4 mirrorless digital cameras. Suitable for scuba, snorkel, surf, pool, and any application in or around the water. Â
This housing requires the addition of a compatible DL Lens Port for waterproof operation. Lens Port not included.
This housing is only compatible with Fujifilm X-T4 cameras as shipped by the manufacturer. Unless otherwise noted, this housing does not accommodate the use of add-on grips, battery grips, eyepieces, LCD covers, or other accessories.Â
Differences in lens and control placement prevent other Fujifilm camera models, including the XT-3, from being used in or adapted to this housing. We are not aware of any other models which may be used in or adapted to this particular housing.
Â
Specifications:200' (60m) depth rating
Compatible with DL system lens ports
Controls are provided for all important camera controls;
Controls are not provided for Fn2, Touch screen, Focus mode selector, Focus stick tilt, or Diopter adjustment knob; Front and rear dials may be rotated but not pressed
1/4-20 thread base mounts with 3.5" spacing
Slightly positive buoyancy in fresh water
Actual buoyancy varies depending on choice of lens and port
4.9 lb (2.22 kg)
9.2 x 7.375 x 6.75" (234 x 187 x 171 mm)
Vacuum valve included (pump sold separately)
Included Ikelite ICS-5 bulkhead connector with manual hotshoe for reliable electrical triggering of underwater strobes; Optional TTL accessories provides automatic exposure with compatible Ikelite DS strobes
ABS-PC construction is fundamentally corrosion-resistant
Made in the USA; Individually inspected for fit and water pressure tested to depth
2 year limited warranty
In the Box:
Housing
Rear O-ring # 0132.59 (installed)
Front O-ring # 0132.45 (installed)
Zoom Gear Retainer # 75900 (installed)
Port Hole Cover # 0200.92 (installed)
Waterproof Bulkhead Cap # 9104.7 (installed)
Base with Left-Hand Quick Release Handle # 4077.67 (installed)
Tool for Zoom Gear Retainer # 0945.06
.050" Hex Key # 0945.11
1/16" Hex Key # 0945.16
Silicone Lubricant 1cc Tube
Optional Accessories
Spare Rear O-Ring # 0132.59 Carry a back-up in case original seal becomes damaged.
Spare Front O-Ring # 0132.45 Carry a back-up in case original seal becomes damaged.
Vacuum Pump with Gauge # 47011 Pressurize the housing to check for leaks prior to entering the water.
Right-Hand Quick Release Handle # 4077.02 Makes a double tray for easier handling and a second attachment point for strobes or lights.
Trigger Extension # 4077.93 Recommended if using the Right-Hand Quick Release Handle. Brings shutter or AF-ON lever out to handle for more comfortable use (requires 2 to extend both controls).
DL4 DS Link TTL Converter # 46082 Fast, accurate, automatic TTL strobe exposure when used together with compatible Ikelite DS strobes.
Cable Top Handle Grip # 4080.07 The most convenient way to carry the system when shooting with two strobe arms.
Adding an external strobe or video light enhances your photos' color and sharpness underwater. If you will be shooting below 45 ft (13m) or in an indoor pool, your photos will be predominantly blue-green without an artificial light source. Read more about strobe options
Â
Â
Â
Â
Â
Â
Â
Â
Â
Â
Ikelite 200DL Underwater Housing for Nikon Z50 Mirrorless Digital Cameras
$ 1,695.00
Ikelite 200DL Underwater Housing for Nikon Z50 Mirrorless Digital Cameras
Ikelite SKU: 71065 | Helix SKU: IK71065
Overview
Nikon Z50Â Mirrorless Cameras
The little brother to Nikon's Z6 and Z7 full frame mirrorless cameras, the Z50 features a 20.9 megapixel APS-C (DX-format) sensor. It records UHD 4K/30p video using the full width of its sensor. A bright 2.36M-dot OLED viewfinder provides a good view for both composition and image review.
The camera body weighs in at just under 1 pound (450 g) and accepts both newer Z-mount lenses and F-mount lenses using the FTZ adapter. The camera's CIPA battery life is 320 shots using the rear LCD or 280 shots using the electronic viewfinder (EVF).
Lens Ports
This housing features our robust Dry Lock (DL) port system. "Dry Lock" refers to the placement of the o-ring on the outside of the port mount. This improves visibility and reduces the chances of water dropping onto your precious camera sensor. DL ports are the lightest on the market, yet robust and capable of standing up to rough surf. Attachment is quick and secure. A system of extensions can accommodate a huge variety of lenses with ease.
Most popular zoom lenses and select lens focus rings can be engaged using simple gearing that puts adjustment right at your fingertips. A large, soft-touch knob on the side of the housing makes fine tuned adjustments a breeze. Zoom and focus gears differ depending on which lens you are using. Zoom gears sold separately.
Confidence
The unique rear seal design prevents accidental twisting or stretching of the o-ring for simple and confident assembly. We have eliminated the need for an o-ring groove or channel which can trap sand, dirt, or debris. Three double-passivated stainless steel locking lid snaps are simple to use and virtually unbreakable. The clear back allows you to see the o-ring form a solid, watertight seal as it closes.
Vacuum Testing
A vacuum valve is installed standard on the side of the housing. The vacuum valve is designed to be low profile to avoid interference with controls. The optional Vacuum Pump with Gauge # 47011 allows you to draw a vacuum on the housing to check for leaks prior to entering the water.
Drawing a vacuum on the system also provides extra security at the surface of the water, especially important when using the housing in rough surf.
Â
M16 Accessory Port
The spare M16 threaded accessory port provides an attachment point for third party accessories including HDMI bulkheads.
TTL Exposure
This housings supports your choice of shooting with manual strobe exposure or adding a TTL converter depending on your application. The flash bulkhead is located on the top of the case to alleviate strain on the sync cord.
You can enjoy the fastest and most accurate TTL exposure on the market by adding the DL1 DS Link TTL Converter # 46056 and a compatible Ikelite DS strobe. The DL1 supports rear curtain synchronization and exposure compensation can be added or subtracted in the camera.
Reliable locking connectors between the hotshoe and bulkhead make it easy to install the TTL hotshoe or carry back up parts when traveling to remote locations.
Built-in Flash
The camera's built-in flash may be used to trigger external fiber optic strobes. Two fiber optic ports are provided on the top of the housing for attachment of compatible fiber optic cords (see compatibility information below). The built-in flash is not usable for lighting a subject underwater.
Ergonomics
Good ergonomics are critical when you need to concentrate on composition, focus, and proper exposure. Large, curved control levers put the most important controls right where you need them: shutter and autofocus (via the AE-L/AF-L button). This combination allows you to shoot with or without back button focus, an advanced technique that is useful for tack sharp focus of super macro and fast moving subjects. Each lever can be extended using the optional Trigger Extension # 4077.93 for perfect spacing when using a right-hand handle.
The rotating controls are all operated intuitively via premium soft-touch knobs. An oversized, lobed knob puts the zoom/focus knob at your fingertips while your left hand stays on the handle. Stainless steel, direct-drive rotating controls are virtually fail-safe and user serviceable and adjustable in a pinch.
All rear camera buttons are accessible by smooth action, hard anodized aluminum push buttons for reliable performance and easy maintenance. These controls are clearly labeled by laser engraving on the back of the housing that never fades or falls off.
Set-Up
The camera mount is front-loading for easy installation and removal. A small mounting plate attaches to the bottom of the camera and secures in the front of the housing. The camera mounting plate does not need to be removed from the camera for surface use or when changing the battery or memory cards. The mounting plate features a 1/4-20 threaded mount on the bottom so that it can be attached to a tripod on the surface.
Viewfinders
The included SuperEye Viewfinder provides an enhanced view of the camera's electronic viewfinder when viewed through a dive mask. The viewfinder removes quickly and easily for the attachment of an optional Straight Magnified Viewfinder # 6890.2 or 45° Magnified Viewfinder (Type 3) # 6891.3.
Â
Camera Compatibility
This housing is only compatible with Nikon Z50 cameras as shipped by the manufacturer. Unless otherwise noted, this housing does not accommodate the use of add-on grips, battery grips, eyepieces, LCD covers, or other accessories.Â
Differences in lens and control placement prevent other Nikon camera models from being used in or adapted to this housing. We are not aware of any other models which may be used in or adapted to this particular housing.
Specifications:
200' (60m) depth rating
Compatible with DL system lens ports
Controls are provided for all camera functions except: Fn1, Fn2, Flash pop-up, Diopter adjustment dial, and Touchscreen;
1/4-20 thread base mounts with 3.5" spacing
Slightly positive buoyancy in fresh water
Actual buoyancy varies depending on choice of lens and port
Housing 4.77 lb (2165 g)
Tray with left handle 11 oz (312 g)
9 x 7 x 6.25" (229 x 178 x 159 mm)
Vacuum valve included (pump sold separately)
Included Ikelite ICS-5 bulkhead connector with manual hotshoe for reliable electrical triggering of underwater strobes; Optional TTL accessories provides automatic exposure with compatible Ikelite DS strobes
ABS-PC construction is fundamentally corrosion-resistant
Made in the USA; Individually inspected for fit and water pressure tested to depth
2 year limited warranty
In the Box
Housing
Rear O-ring # 0132.59 (installed)
Front O-ring # 0132.45 (installed)
Zoom Gear Retainer # 75900 (installed)
Port Hole Cover # 0200.92 (installed)
Waterproof Bulkhead Cap # 9104.7 (installed)
Base with Left-Hand Quick Release Handle # 4077.67 (installed)
Tool for Zoom Gear Retainer # 0945.06
.050" Hex Key # 0945.11
1/16" Hex Key # 0945.16
Silicone Lubricant 1cc Tube
Â
ikelite 200DL Underwater Housing for Sony Alpha A9 Mirrorless Cameras
$ 1,695.00
ikelite 200DL Underwater Housing for Sony Alpha A9 Mirrorless Cameras
ikelite SKU:Â 71473 | Helix SKU:Â 71473
Overview
A full featured and durable waterproof housing for Sony Alpha A9 Mirrorless cameras. Suitable for scuba, snorkel, surf, pool, and any application in or around the water.
Â
- Depth Rating: 200'
- Ikelite 5-Pin Bulkhead Strobe Connector
- Manual Flash Exposure, TTL Optional
- Mechanical Controls
- Access to All Essential Camera Functions
- White ABS/Polycarbonate Body, Clear Back
- Interchangeable DL Lens Port System
- Ships without Required Lens Port
- Vacuum Valve Included
- Made in the USA
Â
Â
Compatibility
This housing is only compatible with the Sony Alpha A9 camera as shipped by the manufacturer. Unless otherwise noted, this housing does not accommodate the use of add-on grips, battery grips, eyepieces, LCD covers, or other accessories.
Differences in lens and control placement prevent other camera models from being used in this housing. We are not aware of any other models which may be used in or adapted to this particular housing.
Specifications
200' (60m) depth ratingCompatible with DL system lens ports
Controls are provided for all important camera controls; Controls are not provided for the Diopter adjustment dial, Multi-selector, Media slot cover switch, Focus mode dial; Focus mode dial lock release button
1/4-20 thread base mounts with 3.5" spacing
Near neutral buoyancy in fresh water
Actual buoyancy varies depending on choice of lens and port
5.0Â lb (2.3 kg)
9Â x 7.2 x 6.5" (229 x 183 x 168 mm)
Vacuum valve included (pump sold separately)
Included Ikelite ICS-5 bulkhead connector with manual hotshoe for reliable electrical triggering of underwater strobes; Optional TTL accessories provides automatic exposure with compatible Ikelite DS strobes
ABS-PC and Lexan construction is fundamentally corrosion-resistant
Made in the USA; Individually inspected for fit and water pressure tested to depth
1 year limited warranty
What's In the Box
HousingRear o-ring # 0132.59
Front o-ring # 0132.45
Base with Left-Hand Quick Release Handle # 4077.67
Port Hole Cover # 0200.92
Zoom Gear Retainer # 75900
Tool for Zoom Gear Retainer # 0945.06
Waterproof Bulkhead Cap # 9104.5
4-40 Hex Key # 0945.11
1/16" Hex Key # 0945.16
1/8" Hex Key # 0945.18
Control + Push Button Tip Assortment # 9249
Silicone Lubricant 1cc Tube # 0184.2
Ikelite 200DLM/A Underwater Housing for Olympus OM-D E-M5 III Mirrorless Cameras
$ 950.00 - Sold Out
Ikelite 200DLM/A Underwater Housing for Olympus OM-D E-M5 III Mirrorless Cameras
The third in the series E-M5 cameras is not just a name change, but a redesigned camera body which is actually several millimeters smaller than its predecessor. The camera features the same 20 megapixel micro four-thirds sensor as the more expensive and highly respected E-M1 Mark II camera. The camera is quite capable with a 121-point hybrid autofocus system and 5-axis in-body image stabilization system. For videophiles, the E-M5 II can capture 4K 30p and 24p, plus high speed 1080/120p.
- 200 ft (60m) depth rating
- Extendable shutter release lever
- Extendable AE-L/AF-L button thumb lever for back button focus
- Interchangeable Dry Lock Micro port system including flat ports, 6"dome ports, and 8" dome ports
- Corrosion-proof ABS-PC construction
- Clear view back with laser engraved control markings
- Ergonomic, field serviceable direct-drive controls
- Accessory ports for optional vacuum system and TTL converter
- Supports LCD tilt
- Made in the USA
Good ergonomics are critical when you need to concentrate on composition, focus, and proper exposure. Large, curved control levers put the most important controls right where you need them: shutter and autofocus (via the AE-L/AF-L button). This combination allows you to shoot with or without back button focus, an advanced technique that is useful for tack sharp focus of super macro and fast moving subjects. Each lever can be extended using the optional Shutter Trigger Extension # 4077.93 for perfect spacing when using a right-hand handle.
All rotating controls are operated intuitively via premium soft-touch knobs. Stainless steel, direct-drive rotating controls are virtually fail-safe and user serviceable and adjustable in a pinch.
Camera buttons are accessible by smooth action, hard anodized aluminum push buttons for reliable performance and easy maintenance. These controls are clearly labeled by laser engraving on the back of the housing that never fades or falls off.
Two 1/4-20 threaded mounting points are included on the bottom of the housing for simple, rotation-free attachment of a tray and handle system. Handles provide improved ergonomics underwater and are the foundation for your lighting mounts. The Tray with Dual Quick Release Handles # 9523.64 is the most popular choice for both handling and attachment of accessories.
Drawing a vacuum on the system also provides extra security at the surface of the water, especially important when using the housing in rough surf.
Get the brightest and sharpest view of the camera's OLED EVF by adding an optional Magnified Viewfinder. The Supereye removes quickly and easily for the attachment of a Straight Enhanced Magnified Viewfinder # 6890.2 or 45° Magnified Viewfinder (Type 3) # 6891.3.
You can enjoy the fastest and most accurate TTL exposure on the market by adding the Olympus TTL Kit # 46032 and a compatible Ikelite DS strobe. Rear curtain flash synchronization is supported. Exposure compensation can be used added or subtracted in the camera.
Reliable locking connectors between the hotshoe and bulkhead make it easy to install the TTL hotshoe or carry back up parts when traveling to remote locations.
This camera does not feature a built-in flash for the triggering of fiber optic strobes.
A bright constant-on video light can be used instead of or in addition to a flash. A constant-on light is not as bright as a strobe flash. Constant-on lights do provide added versatility because they can be used for focus assist and for improved colors when shooting video.
There is a simple rule that brighter is better underwater. A high-quality lighting system can produce professional quality results.
This housing accepts ports from our DLM Port System to accommodate a selection of the best zoom, macro, and wide angle lenses for underwater use. Our custom optical grade acrylic domes components provide the color, clarity, and durability of glass at a fraction of the travel weight and cost.
Durability and corrosion free performance
Our white ABS-PC blend housing provides strength and corrosion free performance year with minimal maintenance. ABS-PC is lighter than aluminum for convenience during travel and less drag underwater. The specially formulated color deflects the sun to keep your camera running cooler, longer. Compared to black or clear housings, the light color provides superior contrast for enhanced view of the camera, LCD screen, and o-ring seal.
Compatibility
This housing is only compatible with the Olympus cameras as shipped by the manufacturer. Unless otherwise noted, this housing does not accommodate the use of add-on grips, battery grips, eyepieces, LCD covers, or other accessories.
Specifications
DLM Type A port mount
Controls for all camera functions except Fn lever, preview button, and diopter adjustment dial
Two 1/4-20 threaded tray mounts with 3" (76mm) spacing
Slightly negative buoyancy in fresh water
Actual buoyancy varies depending on choice of lens and port
2.7 lbs (1238 g)
7.75 x 5.75 x 5.25" (197 x 146 x 133 mm)
ABS-PC, acrylic, and acetal construction
2 year limited warranty
In the Box
Rear O-Ring # 0110 (installed)
Front O-Ring # 0132.36 (installed)
.050" Hex Key # 0945.11
1/16" Hex Key # 0945.16
Silicone Lubricant 1cc Tube
Lens port sold separately; A compatible DLM lens port is required for waterproof operation.
Ikelite 200DLM/A Underwater Housing for Olympus PEN E-PL8 Mirrorless Micro Four-Thirds Digital Camera
$ 1,049.95
Ikelite 200DLM/A Underwater Housing for Olympus PEN E-PL8 Mirrorless Micro Four-Thirds Digital Camera
ikelite SKU: 6951.08 | Helix SKU: 695108
Overview
This housing requires the addition of a compatible lens port for waterproof operation. Lens port not included.
Superb handling
This powerful compact housing packs in all of our latest upgrades to controls and ergonomics. The shutter lever has been updated to a more sensitive and natural feeling curved design. The standard control hugs the side of the housing for comfortable use when hand holding. It can be easily extended using the optional Shutter Trigger Extension  # 4077.93 to put it within easy reach when using a right-hand quick release handle.
Controls are located in the same configuration as on the camera to replicate the muscle memory and familiarity you've developed with your camera on the surface.
Even our push buttons have been redesigned to reduce weight and salt build-up. The video record start/stop button is bright red anodized so that you never miss the action. The back of the housing features laser engraved control symbols which will never fade or fall off.
The camera mount is front-loading for easy installation and removal. A small mounting plate attaches to the bottom of the camera and secures in the front of the housing. The camera mounting plate does not need to be removed from the camera for surface use or when changing the battery or memory cards. The mounting plate features a 1/4-20 threaded mount on the bottom so that it can be attached to a tripod on the surface.
The camera's large, super-bright LCD screen is viewable edge-to-edge through the back of the housing.
True TTL exposure
Light is absorbed as it travels through even short distances underwater, making colors appear dull or monochromatic. To preserve the natural colors of your subject, it's important to stay within arm's reach—no more than 3-4 feet (1m) away.
An integrated TTL circuit is fine-tuned to the Olympus PEN E-PL8 flash exposure protocol for the most accurate exposure possible. The circuit is powered by the strobe for zero maintenance and no batteries to change. Exposure compensation in TTL mode is supported using the camera's built-in control. At this time, only Ikelite DS strobes are capable of powering the circuitry. SEA&SEA, INON, and Nikonos strobes will still enjoy fast recycle times and improved battery life, but must be used in manual exposure modes only.
This housing provides a direct electrical connection to the camera's external flash hot shoe. Cord attachment is as easy as screwing in a light bulb, and the threaded fit prevents accidental detachment during use. The bulkhead connection has been moved to the top of the housing to keep cords out of your way and reduce strain on the cord ends. A variety of sync cord terminations are available for Ikelite, SEA&SEA, INON, or Nikonos strobes for ultimate versatility.
The Olympus PEN E-PL8 camera does not feature a built-in flash. Triggering of fiber optic strobes is not supported at this time. A strobe must be connected by electrical sync cord.
A bright constant-on video light can be used instead of or in addition to a flash. A constant-on light is not as bright as a strobe flash. Constant-on lights do provide added versatility because they can be used for focus assist and for improved colors when shooting video.
Two 1/4-20 threaded mounting points are included on the bottom of the housing for the attachment of a tray and handle system. Handles provide improved ergonomics underwater and are the foundation for your lighting mounts.
There is a simple rule that brighter is better underwater. A high-quality lighting system can produce magazine quality results with almost any camera system.
The Lens Support You Want
It couldn't be more simple to change ports than this system—just press the port on and tighten three thumb screws. Feel positive reinforcement that the port is secure with simple parts you can trust in a remote location.
This housing accepts a variety of ports from our DLM Port System to accommodate all of the most popular zoom, macro, and wide angle lenses. Our custom optical grade acrylic domes components provide the color, clarity, and durability of glass at a fraction of the travel weight and cost.
Lens port sold separately.
Durability and corrosion free performance
Our new white ABS-PC blend housing provides strength and corrosion free performance year with minimal maintenance. The specially formulated color deflects the sun to keep your camera running cooler, longer. Compared to black or clear housings, the light color provides superior contrast for enhanced view of the camera, LCD screen, and o-ring seal.
The unique rear seal design prevents accidental twisting or stretching of the o-ring for simple and confident assembly. We have eliminated the need for an o-ring groove or channel which can trap sand, dirt, or debris. Two double-passivated stainless steel locking lid snaps are simple to use and virtually unbreakable. The clear back allows you to see the o-ring form a solid, watertight seal as it closes.
A spare 1/2-20 threaded accessory port is provided on the side of the housing for easily installation of the optional Vacuum Kit  # 47012. A vacuum kit allows you to pressurize the housing to check for proper assembly prior to entering the water.
Ikelite products are designed, built and tested in the USA. We use locally sourced, top-grade materials. Our housings are built by hand and individually tested for fit and function. Every unit is water pressure tested to 200 feet (60m). We back our products with over 50 years of experience and the best reputation for service within the dive industry.
This housing is only compatible with the PEN E-PL8 camera.
Strobe CompatibilityÂ
Serial number requirements
- AF35: not compatible
- DS50: yes, above serial number 70000
- DS51: yes
- DS125: yes, above serial number 5000
- DS160, DS161: yes
- DS200: yes, above serial number 7163
Electrical sync cord compatibility
- Ikelite-to-Ikelite TTL Sync Cord (TTL) Product 4103.51
- Ikelite-to-Ikelite TTL Dual Sync Cord (TTL) Product 4103.52
- SEA&SEA / INON Strobe-to-Ikelite Non-TTL Sync Cord (Manual) Product 4118.1
- SEA&SEA / INON Strobe-to-Ikelite Non-TTL Dual Sync Cord (Manual) Product 4118.2
- Nikonos SB Strobe-to-Ikelite Non-TTL Sync Cord (Manual) Product 4116.31
- Nikonos SB Strobe-to-Ikelite Non-TTL Sync Cord (Manual) Product 4116.32
Specifications
- 200 ft (60m) depth rating
- DLM Type A port mount
- Controls for all important camera functions; controls are not provided for Fn button or Zoom button
- Ikelite flash bulkhead connector with built-in TTL circuitry
- Two 1/4-20 threaded tray mounts with 3-inch (76mm) spacing
- Slightly negative buoyancy in fresh water
- Actual buoyancy varies depending on choice of lens and port
- 2.9 pounds (1.3 kg)
- 7.5 x 5.9 x 5.2 in (191 x 150 x 132 mm)
- ABS-PC, acrylic, and acetyl construction
What's Included
- Housing
- Housing Rear O-Ring # 0110
- Housing Front O-Ring # 0132.36
- Waterproof bulkhead cap # 9104.5
- Control + Push Button Tip Assortment # 9249.3
- 1/8" Hex Key # 0945.18
- Lubricant # 0184.1
- 1 year manufacturer warranty
Lens port required for waterproof operation. Lens port sold separately.
Ikelite 3' Sync Cord Extension
$ 89.95
Ikelite 3' Sync Cord Extension - 410203
Non-coiled 3 ft (91 cm) long extension cord with Ikelite-style bulkhead on one end and Ikelite-style strobe plug on the other end. Use to position your strobe in a location farther from your housing than accommodated by a normal coiled cord.
Communicates TTL signal when used with compatible strobe, housing and sync cord. The Ikelite-style bulkhead and plug are widely recognized as the most reliable waterproof strobe sync connections available. Built-in strain reliefs reduce stress on cord ends.
Â
Â
Ikelite 45 Degree Magnified Viewfinder for DSLR and Mirrorless Housings (Type 3)
$ 949.95
Ikelite 45 Degree Magnified Viewfinder for DSLR and Mirrorless Housings (Type 3)
Ikelite SKU: 6891.3 | Helix SKU: 68913
Overview
Enjoy enhanced viewing of your camera's viewfinder while creating space for your regulator, making composition more comfortable. Easy installation on almost any Ikelite housing for a DSLR or mirrorless camera.Â
Compatibility
Three versions of this viewfinder are available to provide adequate control clearance. Choose Type 1, 2, or 3 based on your camera and housing model.
The Type 3 viewfinder may be used with any housing that calls for a Type 1 viewfinder. The Type 1 viewfinder cannot be used with housings that require a Type 3.
Refer to the compatibility chart in the Documentation section.
Specifications
Anodized aluminum, glass, and acetyl
1.0X magnification
2.23 x 3.24 x 3.82" (57 x 82 x 97Â mm)
Weighs 11.7 oz (332 g)
In the Box
Viewfinder
Protective cap
Attachment tool # 0945.04
Spare o-ring # 0132.22
Ikelite Action Tray II Extension for Compact Housings
$ 20.00
Ikelite Action Tray II Extension for Compact Housings
Ikelite SKU: 2605.12 | Helix SKU: 2605.12
Overview
Extend the Action Tray II to make a dual tray. The Action Tray II is required to mount to a housing.
Specifications
- Hard anodized aluminum tray
- 5.6 oz (158g)
What's Included
- Extension
- Mounting hardware
Ikelite Action Tray II Extension with DS51 Strobe Arm for ULTRAcompact Housings
$ 55.00
Ikelite Action Tray II Extension with DS51 Strobe Arm for ULTRAcompact Housings
Ikelite SKU: 2605.09 | Helix SKU: 260509
Overview
Add a second strobe to an Action Tray II. The Action Tray II is required to mount to a housing.
Specifications
- Hard anodized aluminum tray
-
6.7 oz (189g)
What's Included
- Action Tray II Extension # 2605.12
- Flex Strobe Arm for Action Tray # 4087.27
Ikelite Action Tray II Extension with Light Arm for ULTRAcompact Housings
$ 55.00
Ikelite Action Tray II Extension with Light Arm for ULTRAcompact Housings
Ikelite SKU: 2605.07 | Helix SKU: 260507
Overview
Add a light any Action Tray II. The Action Tray II is required to mount to a housing.
Specifications
- Hard anodized aluminum tray
- 5.6 oz (158g)
What's Included
- Action Tray II Extension # 2605.12
- Flex Light Arm for Action Tray # 4087.26
Ikelite Action Tray II Extension with Right Handle for Compact Housings
$ 55.00
Ikelite Action Tray II Extension with Right Handle for Compact Housings
Ikelite SKU: 2605.05 | Helix SKU: 260505
Overview
Extend the Action Tray II into a dual handle assembly. The Action Tray II is required to mount to a housing.
Specifications
- Hard anodized aluminum tray
- Aluminum, ABS and rubber handle
- 7.1 oz (200g)
What's Included
- Action Tray II Extension # 2605.12
- Left-Handle Quick Release Handle # 9531.4
Ikelite Action Tray II for Compact Housings
$ 25.00
Ikelite Action Tray II for Compact Housings
Ikelite SKU: 2605.11 | Helix SKU: 260511
Overview
This super slim and streamlined tray is designed specifically for Ikelite Action and ULTRAcompact digital housings. Compared to our standard Tray with Quick Release Handle, the Action tray is lighter and brings the grip closer to the side of the housing for a more comfortable system.
Included is the necessary hardware to mount to Ikelite housings featuring female mounting points with 3" (76mm) spacing, as well as Action housings with central 1/4-20 mounting. The tray is machined specially to prevent rotation when attached to an Action housing.
Specifications
- Hard anodized aluminum tray
- 8.2 oz (233g)
What's Included
- Action Tray II
- Hardware Set for 1/4-20 Thread Housings # 9523.24
- Hardware Set for 12-24 Thread Housings # 9523.25
Ikelite Action Tray II with DS51 Strobe Arm for ULTRAcompact Housings
$ 65.00
Ikelite Action Tray II with DS51 Strobe Arm for ULTRAcompact Housings
Ikelite SKU: 2605.08 | Helix SKU: 260508
Overview
This super slim and streamlined tray is designed specifically for Ikelite Action and ULTRAcompact digital housings. Compared to our standard Tray with Quick Release Handle, the Action tray is lighter and brings the grip closer to the side of the housing for a more comfortable system.
The flex arm accepts any light mount which is compatible with 1/2" Loc-line flex components, including the 1/2" flex mounts offered by Light & Motion. Mounting of strobes or larger video lights is not recommended. To mount a strobe, use product # 2605.08 instead.
Add the Action Tray II Extension with Light Arm # 2605.07 for a dual handle tray.
Included is the necessary hardware to mount to Ikelite housings featuring female mounting points with 3" (76mm) spacing, as well as Action housings with central 1/4-20 mounting. The tray is machined specially to prevent rotation when attached to an Action housing.
This tray is not suitable for use with our housings for Mirrorless cameras or larger digital housings with stainless steel lidsnaps. Refer to the housing webpage for the correct tray recommendation.
Specifications
- Hard anodized aluminum tray
- 9.3 oz (263g)
What's Included
- Action Tray II # 2605.11
- Flex Strobe Arm for Action Tray # 4087.27
- Hardware Set for 1/4-20 Thread Housings # 9523.24
- Hardware Set for 12-24 Thread Housings # 9523.25
Ikelite Action Tray II with Left Handle for Compact Housings
$ 65.00
Ikelite Action Tray II with Left Handle for Compact Housings
Ikelite SKU: 2605.04 | Helix SKU: 260504
Overview
This super slim and streamlined tray is designed specifically for Ikelite Action, ULTRAcompact, and smaller compact digital housings. Compared to our standard Tray with Quick Release Handle, the Action tray is lighter and brings the handle closer to the side of the housing for a more comfortable grip.
The Ikelite Quick Release handle has become a favorite over the years for attachment and release of your lighting arm at the touch of a button. Accept no substitute. Add the Action Tray II Extension with Right Handle # 2605.05 for a dual handle tray.
Included is the necessary hardware to mount to Ikelite housings featuring female mounting points with 3" (76mm) spacing, as well as Action housings with central 1/4-20 mounting. The tray is machined specially to prevent rotation when attached to an Action housing.
This tray is not suitable for use with our housings for Mirrorless cameras or larger digital housings. Refer to the housing webpage for the correct tray recommendation.
Specifications
- Hard anodized aluminum tray
- Aluminum, ABS and rubber handle
- 10.6 oz (299g)
What's Included
- Action Tray II # 2605.11
- Left-Handle Quick Release Handle # 9531.3
- Hardware Set for 1/4-20 Thread Housings # 9523.24
- Hardware Set for 12-24 Thread Housings # 9523.25
Â
Ikelite Action Tray II with Light Arm for ULTRAcompact Housings
$ 65.00
Ikelite Action Tray II with Light Arm for ULTRAcompact Housings
Ikelite SKU: 2605.06 | Helix SKU: 260506
Overview
This super slim and streamlined tray is designed specifically for Ikelite Action and ULTRAcompact digital housings. Compared to our standard Tray with Quick Release Handle, the Action tray is lighter and brings the grip closer to the side of the housing for a more comfortable system.
The flex arm accepts any light mount which is compatible with 1/2" Loc-line flex components, including the 1/2" flex mounts offered by Light & Motion. Mounting of strobes or larger video lights is not recommended. To mount a strobe, use product # 2605.08 instead.
Add the Action Tray II Extension with Light Arm # 2605.07 for a dual handle tray.
Included is the necessary hardware to mount to Ikelite housings featuring female mounting points with 3" (76mm) spacing, as well as Action housings with central 1/4-20 mounting. The tray is machined specially to prevent rotation when attached to an Action housing.
This tray is not suitable for use with our housings for Mirrorless cameras or larger digital housings with stainless steel lidsnaps. Refer to the housing webpage for the correct tray recommendation.
Specifications
- Hard anodized aluminum tray
- 8.2 oz (233g)
What's Included
- Action Tray II # 2605.11
- Flex Light Arm for Action Tray # 4087.26
- Hardware Set for 1/4-20 Thread Housings # 9523.24
- Hardware Set for 12-24 Thread Housings # 9523.25
Ikelite AF35 Optical TTL Strobe
$ 429.95 - Sold Out
Ikelite AF35 Optical TTL Strobe - 4035
The AF35's built-in sensor transmits data from the camera's flash to the AF35 strobe, varying the strobe's power automatically to replicate TTL exposure. The AF35 sensor is positioned to provide the most reliable strobe triggering possible without exposed cables which require maintenance and can tangle or break.
Ikelite Aluminum Top Handle for Digital & DSLR
$ 289.95
Ikelite Aluminum Top Handle for Digital &Â DSLR - 408003
Â
Ikelite Aluminum Top Handle for DSLR, Mirrorless, and Compact Digital Housings
$ 189.95
Ikelite Aluminum Top Handle for DSLR, Mirrorless, and Compact Digital Housings
Ikelite SKU: 4080.08 | Helix SKU: 408008
Overview
Span your dual tray and arm system with this versatile top handle. The unique slotted ball arm doubles as both a handle and a mounting location for additional lighting, or a 67mm threaded lens holder. Works with dual trays for Compact Digital or DSLR housings with two lighting arms attached.
Attachment of this top handle requires that you have two strobe arms each having Clamps with Auxiliary Mount # 4081.22 at the base of each arm. This clamp comes standard with newer strobe arms # 4080.05 and # 4080.06.
Specifications
(2) Auxiliary Ball Mount # 4081.71
(2) Ball Clamp for Lightweight Accessories # 4081.21
7" Ball Arm # 4081.07
Ikelite Anti-Reflection Ring for Canon 10-18mm STM Lens
$ 10.00
Ikelite Anti-Reflection Ring for Canon 10-18mm STM Lens
Ikelite SKU: 0923.07 | Helix SKU: 092307
Overview
A self-adhesive vinyl label covers the white lettering and ring details on the front of the lens to reduce reflections when used behind a dome port underwater.
Designed specifically for use with the following lenses:
- EF-S 10-18mm f/4.5–5.6 IS STM
Ikelite Anti-Reflection Ring for Canon 16-35mm f/2.8 II USM Lens
$ 10.00
Ikelite Anti-Reflection Ring for Canon 16-35mm f/2.8 II USM Lens
Ikelite SKU: 092304 | Helix SKU: 092304
Overview
A self-adhesive vinyl label covers the white lettering and ring details on the front of the lens to reduce reflections when used behind a dome port underwater.
Designed specifically for use with the Canon 16-35mm f/2.8 II USM lens.
Ikelite Anti-Reflection Ring for Canon 16-35mm f/2.8 III USM Lens
$ 10.00
Ikelite Anti-Reflection Ring for Canon 16-35mm f/2.8 III USM Lens
Ikelite SKU: 0923.05 | Helix SKU: 092305
Overview
A self-adhesive vinyl label covers the white lettering and ring details on the front of the lens to reduce reflections when used behind a dome port underwater.
Designed specifically for use with the Canon 16-35mm f/2.8 III USM lens.
