Rode VideoMic Directional Video Condenser Microphone w/Mount
$ 149.00 - Sold Out
The RODE VideoMic Direction Video Condenser Microphone is a professional-grade shotgun microphone. Based on the latest Film industry technology, the VideoMic is designed specifically for use with high quality digital video cameras. The microphone exhibits low noise and an unusually wide bandwidth for its size. It is ultra lightweight, yet rugged due to it's ABS construction. The VideoMic is powered by a standard 9 V battery and offers a low battery LED status indicator and a switchable high pass filter to reduce unwanted low frequency rumble. The VideoMic attaches to any camcorder that has the standard camera-shoe fitting and utilizes a stereo mini jack for audio output. RODE VideoMic Shotgun Microphone Features Broadcast and studio sound quality Rugged reinforced ABS construction two step high-pass filter - flat or 80 Hz integrated shock mount 9 V battery operation condenser transducer low noise circuitry low handling noise includes windscreen integrated camera-shoe mount
RODE VideoMic Pro with Rycote Lyre Suspension Mount
$ 249.00 $ 229.00 - Sold Out
RODE VideoMic Pro with Rycote Lyre Suspension Mount
The RØDE VideoMic Pro is a true shotgun microphone designed for use with camcorders, DSLR cameras and portable audio recorders as a source of primary and reference audio.
At the heart of the VideoMic Pro is an all-new 1/2" condenser capsule that provides broadcast-quality audio via a 3.5mm minijack connector (outputting the mono signal to both left and right channels) with an incredibly low self-noise of just 14db. A super-cardioid polar pattern ensures that surrounding audio is minimised, and your recording is focused on the subject in front of the camera.
The integrated Rycote® Lyre® based shock mounting system separates the VideoMic Pro capsule and electronics from its mount, providing isolation from external physical factors that may cause unwanted rumble and vibrations in the microphone. Constructed from a single piece of hard-wearing thermoplastic, the Lyre® provides superior acoustic suspension to traditional elastic solutions, and will never wear out, sag or snap.
Easily accessible on the rear face of the microphone are the power, filter and level controls. In addition to the microphone's native 40Hz-20kHz response a selectable high-pass filter at 80Hz is available, which will prevent low end noise such as air conditioners and traffic from being recorded.
Below these controls are the level settings, which attenuate or boost the recorded level as required. The -10dB level attenuation (or PAD) is ideal for recording loud sound sources, such as live music, motorsport, or interviews where the subject is very close to the camera. The +20dB level boost is designed for use with DSLR cameras, allowing the user to reduce the camera's preamp level (or mic-input level), effectively reducing the amount of noise generated by the camera's comparatively low quality audio circuitry.
The microphone uses a standard sized shoe mount for on camera use, and features a 3/8" thread in the base of the mount for easy boom pole mounting.
The VideoMic pro is battery powered, and provides over 70 hours recording from a single 9V battery.
The RØDE VideoMic is designed and made in Australia, and covered by RØDE Microphones' industry leading 10 year warranty.
- Rycote® Lyre® shock mounting onboard
- All-new capsule with lower noise and higher sensitivity
- Broadcast recording quality condenser microphone
- Compact form factor (150mm/6” length)
- Ultra lightweight (85g/3oz)
- 9V battery powered - over 70 hours use (alkaline)
- Integrated shock mounting
- Integrated foam windscreen
- 3.5mm stereo mini-jack output (dual mono)
- Two step High Pass Filter (flat, 80Hz)
- Three position level control (-10dB, 0, +20dB)
- Camera shoe mount with 3/8” thread for easy boompole mounting
- 10 year extended warranty when you register your microphone
Rode VideoMicro Compact On-Camera Microphone VideoMicro
$ 59.00 - Sold Out
Rode VideoMicro Compact On-Camera Microphone
RODE SKU: VideoMicro | Helix SKU: RMVideoMicro
Overview
- Compact size and lightweight - only 80mm (3’) long and 42gm (1.5oz)
- All-metal microphone body
- No battery required (powered by camera plug-in power - min 3V)
- Rycote® Lyre® shock mount included
- Deluxe furry windshield included
- Designed and manufactured in Australia
- Two year extended warranty when you register your microphone
The VideoMicro is a compact microphone designed to improve the audio quality of your videos. It incorporates a high-quality cardioid condenser microphone capsule for great quality audio recordings when used with a wide range of cameras. A directional microphone, the VideoMicro reduces distracting peripheral sounds and focusses on the audio in front of the camera. Its pickup is more forgiving than RØDE’s other on-camera microphones providing a more natural sound when recording indoors. Perfect for capturing incredible audio to accompany inspiring vision. The microphone body is made from aluminum, giving it a high level of RF rejection, and is finished in RØDE’s high-grade ceramic anti-glare black coating. Included with the VideoMicro is a camera shoe mount featuring a Rycote Lyre shock mount. Featuring a suspension structure composed of a hard-wearing thermoplastic, it is far more effective at minimising unwanted vibrations, handling and cable-borne noise than traditional elastic suspensions. Virtually indestructible, the Rycote Lyre will never sag, snap, wear out or require rethreading to maintain its effectiveness. Also included is the WS9 synthetic furry wind shield with foam inner cell, designed for use in outdoor scenarios where wind and environmental noise can inhibit recordings. Optionally available is the RØDE SC7, a TRS to TRRS cable that allows the VideoMicro to be used with smartphones, to capture crystal clear, directional sound for video and video applications such as Periscope.
VideoMicro Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter |
| Capsule | 0.50" |
| Polar Pattern |  |
| Address Type | End |
| Frequency Range | 100Hz - 20kHz |
| Maximum SPL | 140dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Sensitivity | -33.0dB re 1 Volt/Pascal (22.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 20dB-A |
| Power Options | Phantom Power Required |
| Weight | 42gm |
| Dimensions | 21mmH x 21mmW x 80mmD |
| Output |  |
| Warranty | 1 year with free extension to 2 years following registration here |
Rode Vlogger Kit - iOS Edition for iOS devices
$ 149.00 - Sold Out
Rode Vlogger Kit - iOS Edition for iOS devices
Rode SKU: VLOGVMML | Helix SKU: RMVLOGVMML
Overview
The iOS Vlogger Kit contains everything you need to get professional results when filming using your iPhone. The VideoMic Me-L microphone connects directly to your device, delivering crisp, clear, directional sound for any application. The SmartGrip secures your device firmly in place for stable recording and connects seamlessly to the Tripod 2 for either handheld or tabletop use, while the MicroLED ensures all your shots are perfectly lit.
Key Features:
- Complete iPhone filmmaking kit
- Directional sound pickup to reduce background noise
- MicroLED light offers over four hours operation on a single charge
- Three-position tripod for handheld or static use
- Gimbal tripod head for accurate camera positioning
- All-metal mount with rubberised grips for phones 65mm to 85mm wide
- All-in-one mobile filmmaking kit, including a RØDE VideoMic, Tripod 2, SmartGrip, MicroLED and accessories
- Options for iOS (Lightning), Android (USB-C) devices and a Universal Edition (3.5mm)
- High-quality microphone that delivers professional sound in any recording situation
- Three-position tripod for either handheld or tabletop use
- MicroLED on-camera light with eight coloured filters for flawless shots
- Lightweight all-metal mount with rubberised grips, accommodates phones 65mm to 85mm wide
IN THE BOX:
- VideoMic Me-C Microphone
- Rubber Clip
- WS9 Windshield
- SmartGrip
- Tripod 2
- MicroLED On-camera Light
- Clip-on Diffuser
- 8 Coloured Filters
- USB-C Cable for recharging the MicroLED on-camera light
Rode Vlogger Kit - USB-C Edition for compatible phones
$ 149.00 - Sold Out
Rode Vlogger Kit - USB-C Edition for compatible phones
Rode SKU: VLOGVMMC | Helix SKU: RMVLOGVMMC
Overview
The USB-C Vlogger Kit contains everything you need to get professional results when filming using your USB-C equipped mobile phone. The VideoMic Me-C microphone connects directly to your device, delivering crisp, clear, directional sound for any application. The SmartGrip secures your device firmly in place for stable recording and connects seamlessly to the Tripod 2 for either handheld or tabletop use, while the MicroLED ensures all your shots are perfectly lit.
Key Features:
- Complete USB-C mobile fi lmmaking kit
- Directional sound pickup to reduce background noise
- MicroLED light offers over four hours operation on a single charge
- Three-position tripod for handheld or static use
- Gimbal tripod head for accurate camera positioning
- All-in-one mobile filmmaking kit, including a RØDE VideoMic, Tripod 2, SmartGrip, MicroLED and accessories
- Options for iOS (Lightning), Android (USB-C) devices and a Universal Edition (3.5mm)
- High-quality microphone that delivers professional sound in any recording situation
- Three-position tripod for either handheld or tabletop use
- MicroLED on-camera light with eight coloured filters for flawless shots
- Lightweight all-metal mount with rubberised grips, accommodates phones 65mm to 85mm wide
|
IN THE BOX
|
RODE VMGO Video Mic GO Lightweight On-Camera Microphone Super-Cardio
$ 99.00 - Sold Out
RODE VMGO Video Mic GO Lightweight On-Camera Microphone Super-Cardio
- High quality directional microphone
- No battery required
- Integrated Rycote® Lyre® shock mounting
- Our lightest mic at only 73g
- Rugged reinforced ABS construction
- Windshield included
- 3.5mm mini-jack output
- Integrated cold-shoe mount with 3/8” thread
- Two year extended warranty when you register your microphone
Clear, directional audio on the GO!
Compact and light weight by design, the VideoMic GO delivers clear, crisp, directional audio with incredible ease of use. Its tight pickup area focuses directly in front of the microphone and reduces other surrounding sounds, ensuring that your subject is isolated from distracting background noise.
The integrated Rycote® Lyre® shock mount isolates your microphone from bumps and vibrations that could otherwise interfere with your sound.
Constructed from a single piece of hard-wearing thermoplastic, the Lyre® provides superior acoustic suspension to traditional elastic solutions, and will never wear out, sag or snap.
The VideoMic GO has no complicated switches or settings and is powered by your camera's external microphone input, requiring no batteries to operate, ensuring you never miss a great shot.
The VideoMic GO is designed and made in Australia.
| Acoustic Principle | Line Gradient |
| Active Electronics | JFET impedance converter with bipolar output buffer |
| Capsule | 0.50" |
| Polar Pattern |  |
| Address Type | End |
| Frequency Range | 100Hz - 16kHz |
| Maximum SPL | 120dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Sensitivity | -35.0dB re 1 Volt/Pascal (17.80mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 34dB-A |
| Weight | 73.00gm |
| Dimensions | 79.00mmH x 73.00mmW x 167.00mmD |
| Output | |
| Warranty | 1 year with free extension to 2 years |
Rode VXLR Adapter for VideoMic Mini-Jack Female to XLR Male
$ 12.99 - Sold Out
RODE VXLR Minijack to XLR Adaptor
The RODE VXLR Minijack to XLR Adaptor is used to convert a 3.5 mm minijack to a 3 pin XLR. Use the VXLR adaptor to hook your Video Mic up to your studio gear. It's that simple!
Weight:
48.00gm
Dimensions:
58.00mmH x 19.00mmW x 19.00mmD
RODE WS2 Pop Filter / Wind Shield
$ 19.99 - Sold Out
Provides additional protection for the microphone capsule against any wind noise or plosives. Suits Broadcaster, K2, NTK, NT1-A, NT2-A, NT1000, NT2000, Podcaster, Procaster
| Weight | 10.00gm |
| Dimensions | 110.00mmH x 85.00mmW x 85.00mmD |
| Warranty | 1 year |
RODE WS3 Pop Filter / Wind Shield
$ 19.99 - Sold Out
Provides additional protection for the microphone capsule against any wind noise or plosives. Suits NT3, M3
RODE WS4 Pop Filter / Wind Shield
$ 19.99
Provides additional protection for the microphone capsule against any wind noise or plosives. Suits NT4
RODE WS5 Pop Filter / Wind Shield
$ 19.99 - Sold Out
RODE WS5 Pop Filter / Wind Shield
The WS5 windshield provides additional protection for the microphone capsule against any wind noise or plosives. Suits NT5, NT55, M5
| Weight | 1.00gm |
| Dimensions | 48.00mmH x 42.00mmW x 42.00mmD |
| Warranty | 1 year |
RODE WS6 Pop Filter / Wind Shield
$ 59.00 - Sold Out
Deluxe Windshield comprised of open cell foam and fur sleeve. Suits NTG-1, NTG-2, VideoMic and shotguns with a maximum slot length of 160.5mm (6 1/4?) and a diameter of 21-22.5mm
Rode WSVM Pop Filter/Wind Shield
$ 11.99
The Rode WSVM Pop Filter Wind Shield is designed for use with Rode Videomic, NTG1 and NTG2. The WSVM provides additional protection for the microphone capsule against any wind noise or plosives.
- Weight: 4.00gm
- Dimensions: (H x W x D)50 x 50 x 162mm
|
Rode Windscreens
|
WS6
|
WS7
|
WSVM
|
|---|---|---|---|
|
Compatible with NTG1
|
✓
|
✓
|
|
|
Compatible with NTG2
|
✓
|
✓
|
|
|
Compatible with NTG3
|
✓
|
||
|
Compatible with Videomic
|
✓
|
||
|
Functions as a Pop Filter
|
✓
|
✓
|
RØDE HS2 Headset Microphone, Black Color, Large Size
$ 449.00 - Sold Out
RØDE HS2 Headset Microphone, Black Color, Large Size
RØDE SKU: HS2-BL | Helix SKU: RMHS2BL
Overview
The RØDE HS2 is a low profile, ergonomic and lightweight headset microphone that provides clean, clear and pronounced audio for any application where the microphone needs to be in close proximity to presenter's mouth.
The result of an extensive and complete redesign process, the RØDE HS2 features an adjustable corrosion resistant stainless spring-steel boom arm and headband connected to pliable hypoallergenic silicone ear strips for maximum flexibility and user comfort.
Coated in a durable ceramic painted finish in either black (HS2-B) or pink (HS2-P) the HS2 is also available in two different sizes (small or large) to ensure the perfect fit and function for any individual.
The headset is connected via a 1.2m (4') braid shielded, Kevlar® reinforced cable, terminating at a gold plated 3.5mm TRS output with a removable locking nut to ensure a secure connection to a wide range of recording devices and wireless transmitters, including the RØDE Filmmaker and Newsshooter kits.
The HS2's light weight, comfortable fit, low self-noise, minimal appearance and user friendly omni-directional polar pattern make it an ideal microphone for film, television, video, theatre, house of worship and live vocal performance.
- Updated low-profile ergonomic design
- Ultra-Lightweight construction for complete comfort
- Adjustable corrosion resistant stainless spring steel boom arm and headband
- Flexible hypoallergenic sillicone ear strips
- Durable ceramic painted finish available in black or pink
- Available in small or large sizes
- Omni-directional polar pattern
- Low handling noise
- Includes Mini-furry and pop filter / windshield
- 1.2m Kevlar reinforced braid shielded cable
- Gold plated 3.5mm TRS output with removable locking nut
- Five year extended warranty when you register your microphone
What's In The Box
HS2 Lightweight headset microphone
Pop Filter (black)
Cable Management clip
Mini Furry
Specifications
| Acoustic Principle | Permanently Polarised Condenser |
| Active Electronics | JFET impedance converter |
| Address Type | Omni |
| Frequency Range | 60Hz - 18kHz |
| Output Impedance | 3000Ω |
| Maximum SPL | 122dBSPL |
| Maximum Output Level | 189.0mV (@ 1kHz, 1% THD into 1KΩ load) |
| Sensitivity | -47.2dB re 1 Volt/Pascal (4.70mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 36dBA |
| Weight | 20g |
| Dimensions | 50mmH x 124mmW x 205mmD |
| Warranty | 1 year with free extension to 5 years following registration |
RØDE HS2 Headset Microphone, Pink Color, Large Size
$ 449.00 - Sold Out
RØDE HS2 Headset Microphone, Pink Color, Large Size
RØDE SKU: HS2-PL | Helix SKU: RMHS2PL
Overview
The RØDE HS2 is a low profile, ergonomic and lightweight headset microphone that provides clean, clear and pronounced audio for any application where the microphone needs to be in close proximity to presenter's mouth.
The result of an extensive and complete redesign process, the RØDE HS2 features an adjustable corrosion resistant stainless spring-steel boom arm and headband connected to pliable hypoallergenic silicone ear strips for maximum flexibility and user comfort.
Coated in a durable ceramic painted finish in either black (HS2-B) or pink (HS2-P) the HS2 is also available in two different sizes (small or large) to ensure the perfect fit and function for any individual.
The headset is connected via a 1.2m (4') braid shielded, Kevlar® reinforced cable, terminating at a gold plated 3.5mm TRS output with a removable locking nut to ensure a secure connection to a wide range of recording devices and wireless transmitters, including the RØDE Filmmaker and Newsshooter kits.
The HS2's light weight, comfortable fit, low self-noise, minimal appearance and user friendly omni-directional polar pattern make it an ideal microphone for film, television, video, theatre, house of worship and live vocal performance.
- Updated low-profile ergonomic design
- Ultra-Lightweight construction for complete comfort
- Adjustable corrosion resistant stainless spring steel boom arm and headband
- Flexible hypoallergenic sillicone ear strips
- Durable ceramic painted finish available in black or pink
- Available in small or large sizes
- Omni-directional polar pattern
- Low handling noise
- Includes Mini-furry and pop filter / windshield
- 1.2m Kevlar reinforced braid shielded cable
- Gold plated 3.5mm TRS output with removable locking nut
- Five year extended warranty when you register your microphone
What's In The Box
HS2 Lightweight headset microphone
Pop Filter (black)
Cable Management clip
Mini Furry
Specifications
| Acoustic Principle | Permanently Polarised Condenser |
| Active Electronics | JFET impedance converter |
| Address Type | Omni |
| Frequency Range | 60Hz - 18kHz |
| Output Impedance | 3000Ω |
| Maximum SPL | 122dBSPL |
| Maximum Output Level | 189.0mV (@ 1kHz, 1% THD into 1KΩ load) |
| Sensitivity | -47.2dB re 1 Volt/Pascal (4.70mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 36dBA |
| Weight | 20g |
| Dimensions | 50mmH x 124mmW x 205mmD |
| Warranty | 1 year with free extension to 5 years following registration |
RØDE K2 - Variable Pattern Studio Tube Condenser Microphone
$ 699.00
RØDE K2 - Variable Pattern Studio Tube Condenser Microphone
RØDE SKU: K2 | Helix SKU: RMK2
Overview
Seamlessly variable dual 1" condenser valve microphone featuring continually variable polar pattern (omni through cardioid to figure 8).
- Large 1" capsule with gold sputtered diaphragm and internal shock mounting
- Ultra low noise
- Wide dynamic range
- Class ‘A’ valve circuitry
- Hand-selected and graded 6922 twin-triode valve
- Dedicated Power Supply
- High strength welded and heat-treated steel mesh head
- Continuously variable polar patterns. From omni, through cardioid to figure 8, controlled at the power supply.
- 10 year extended warranty when you register your microphone
The RØDE K2 is a premium valve condenser microphone featuring dual 1” gold sputtered diaphragms. Infinitely variable control of the polar pattern from omnidirectional through cardioid and bidirectional/figure-8 provides the freedom and flexibility to excel in any recording situation.
High-performance specifications (including a maximum SPL of 162dB) are combined with the character and subtleties of the legendary mics of the 1950s to provide a microphone that not only provides world-class vocals but is perfectly at home recording a wide range of instruments both up-close or in a wider ‘room’ capacity.
The RØDE K2 microphone is designed and made in Australia, and covered by RØDE Microphones' industry leading 10 year warranty.
Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | Valve/tube impedance converter with bipolar output buffer |
| Capsule | 1.00" |
| Polar Pattern |
 
|
| Address Type | Side |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 200Ω |
| Maximum SPL | 162dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 30.0mV |
| Sensitivity | -36.0dB re 1 Volt/Pascal (16.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 10dB-A |
| Power Options |  |
| Weight | 815.00gm |
| Dimensions | 208.00mmH x 55.00mmW x 55.00mmD |
| Output |  |
| Warranty | 1 year with free extension to 10 years following registration |
RØDE NT-USB USB Condenser Microphone
$ 199.00 - Sold Out
RØDE NT-USB USB Condenser Microphone
RØDE SKU: NT-USB | Helix SKU: RMNTUSB
Overview
- High quality studio microphone with the convenience of USB connectivity
- Pop shield, Tripod desk stand, ring mount, storage pouch and 6m (20’) USB cable included
- 3.5mm stereo headphone jack for zero-latency monitoring
- Direct mix control between mic input and source output
- Compatible with Apple® iPad
- Two year extended warranty when you register your microphone
The NT-USB is a highly versatile side-address microphone that is ideal for recording singing and musical performances in addition to spoken applications such as podcasting and voice-over.
It is fully compatible with all mainstream recording applications on both Windows and Mac OS based computers, as well as the Apple iPad using RØDE Rec, GarageBand, or any other recording app that accepts an external microphone. Use on the Apple iPad requires a suitable USB connection adaptor, such as the Apple Camera Connection Kit.
The body of the NT-USB features a zero-latency stereo headphone monitoring (3.5mm) jack, which allows you to monitor the microphone input in realtime, along with dials to adjust the monitoring level and mix between the computer/iPad audio and the microphone input.
A premium pop-filter is included, which fits onto the base of the mic, positioning the filter the ideal distance from the capsule to minimise plosives (hard ‘B’, ‘T’ or ‘P’ sounds that produce a harsh sound) during singing or speech. Also provided is a high-quality stand mount with industry standard 3/8” thread, desktop tripod stand that allows the NT-USB to sit at a comfortable height on a tabletop, and a pouch for storage of the microphone when not in use.
Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter with bipolar output buffer, A/D converter 16bit 48kHz |
| Capsule | 0.50" |
| Polar Pattern | |
| Resolution | 16-bit |
| Address Type | Side |
| Frequency Range | 20Hz - 20kHz |
| Maximum SPL | 110dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Power Options |  |
| Weight | 520gm |
| Dimensions | 184mmH x 62mmW x 50mmD |
| Output | |
| Warranty | 1 year with free extension to 2 years following registration |
RØDE NT1 Condenser Microphone Cardioid
$ 249.00 - Sold Out
RØDE NT1 Condenser Microphone Cardioid
RØDE SKU: NT1 | Helix SKU: RMNT1
Overview
- Large 1" condenser capsule with gold-plated membrane
- Cardioid polar pattern
- Internal Rycote® Lyre® based capsule shock mounting system
- Ultra-low noise, self noise of only 4.5dB (A)
- State-of-the-art surface mount electronics
- Available with included RM2 mount (NT1-SINGLE) or with SMR shock mount (NT1-KIT)
- 10 year extended warranty when you register your microphone
The NT1 is a revolutionary new 1" diaphragm condenser microphone from RØDE.
Although the body of the new NT1 closely resembles the NT1-A, the microphone has been completely redesigned from the ground up, with the only shared component being the mesh grille.
RØDE’s design engineers approached the NT1 as a marriage of innovation and tradition, starting with the capsule which is a completely new design. Codenamed the HF6, it is the perfect example of RØDE’s fusion of artistic design approaches and cutting-edge manufacturing techniques, and features a sound signature reminiscent of the famous microphones of old while at the same time exhibiting extremely low noise.
It has been developed with a focus on detailed midrange response, coupled with silky smooth high frequencies, and warm, round, bass reproduction to make the NT1 an absolute standout in its class.
In another world-first for RØDE, the transducer itself is suspended inside the microphone using Rycote’s industry-leading Lyre system, minimizing external vibrations at the capsule level. The capsule is then married to high-grade electronics that have been designed to provide the lowest noise level of any studio microphone available. The NT1 is an incredibly quiet microphone, measuring only 4.5dBA of self-noise.
Its body is machined from 6061 aluminium and then nickel plated for resistance against corrosion. Finally it is coated in a durable, military-grade ceramic layer, using advanced electrostatic application techniques developed by RØDE to ensure an extremely hard wearing finish that is resistant to scratches or marks.
The NT1 is supplied with the revolutionary new RØDE SMR shock mount. Featuring a unique double-Lyre suspension system, the SMR enhances the existing superior vibration cancellation of Rycote’s Lyre system by using a smaller inner Lyre to act as a tensioning element. This maintains each Lyre in the neutral position where it is most efficient at cancelling vibration. The SMR’s removable all-metal pop filter is as effective as it is visually striking, providing an integrated solution for plosive protection that is easily washable and designed to last as long as the shock mount and microphone.
The NT1 is designed and made in Australia, and is covered by RØDE's industry-leading 10 year warranty.
NT1 Specifications:
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter with bipolar output buffer |
| Capsule | 1.00" |
| Polar Pattern | |
| Address Type | Side |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 100Ω |
| Maximum SPL | 132dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 8.0mV |
| Sensitivity | -29.0dB re 1 Volt/Pascal (35.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 4dB-A |
| Power Options |
 
|
| Weight | 440.00gm |
| Dimensions | 187.00mmH x 50.00mmW x 50.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RØDE NT1-A Cardioid Large-Diaphragm Condenser Microphone
$ 229.00 - Sold Out
RØDE NT1-A Cardioid Large-Diaphragm Condenser Microphone
RØDE SKU: NT1-A | Helix SKU: RMNT1A
Overview
Incredibly quiet 1" cardioid condenser microphone
- Large 1” capsule with gold plated diaphragm
- Cardioid polar pattern
- Ultra low noise, self noise of only 5dB (A)
- Wide dynamic range
- True condenser (externally biased)
- Internal capsule shock mounting
- Includes RØDE SM6 shock mount, pop filter and dust cover
- 10 year extended warranty when you register your microphone
The RØDE NT1-A 1" cardioid condenser microphone has become an industry standard; delivering the warmth, extended dynamic range, clarity and high SPL capability typically only featured on some of the world’s most expensive microphones.
With a self-noise level of only 5dBA it is widely recognised (along with the NT1) as one the world's quietest studio microphones. This low noise makes it an ideal for vocal microphone as well as perfect for recording guitars and percussion.
Packaged in the 'Complete Vocal Recording Solution', the NT1-A includes everything you need to get a truly professional vocal recording and is ideal for home studio recording.
A studio grade pop shield and shock mount is included, along with a premium 20' microphone cable, dust cover, and an instructional DVD packed with recording tips.
The RØDE NT1-A large diaphragm 1" cardioid condenser microphone is designed and made in Australia, and covered by RØDE Microphones' industry leading 10 year warranty.
Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter with bipolar output buffer |
| Capsule | 1.00" |
| Polar Pattern | |
| Address Type | Side |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 100Ω |
| Maximum SPL | 137dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 13.7mV |
| Sensitivity | -31.9dB re 1 Volt/Pascal (25.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 5dB-A |
| Power Options |
+48V phantom power required from mixer or interface
|
| Weight | 326.00gm |
| Dimensions | 190.00mmH x 50.00mmW x 50.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RØDE NT1000 Vocal Condenser Microphone
$ 329.00 - Sold Out
RØDE NT1000 Vocal Condenser Microphone
RØDE SKU: NT1000 | Helix SKU: RMNT1000
Overview
Versatile 1" cardioid condenser microphone
- HF2 1” capsule with gold-plated diaphragm
- Cardioid polar pattern
- True condenser (externally biased)
- Full frequency response
- Ultra low noise
- High strength welded and heat-treated mesh head
- Internal capsule shock mounting
- 10 year extended warranty when you register your microphone
With its ultra-low 6dBA self-noise and transformerless circuitry, the RØDE NT1000 exhibits exceptional performance when recording both vocals and instruments.
Voiced for versatility, it has been hailed by many as the ultimate microphone for grand piano and drum overheads. The NT1000 is also a fantastic vocal microphone.
The RØDE NT1000 microphone is designed and made in Australia, and covered by RØDE's industry leading 10 year warranty.
Specifications
|
Acoustic Principle |
Pressure Gradient |
| Active Electronics | Unity-gain closed-loop impedance converter; JFET input with bipolar buffering |
| Capsule | 1.00" |
| Polar Pattern | |
| Address Type | Side |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 100Ω |
| Maximum SPL | 140dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 13.0mV |
| Sensitivity | -36.0dB re 1 Volt/Pascal (16.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 6dB-A |
| Power Options |
|
| Weight | 682.00gm |
| Dimensions | 209.00mmH x 54.00mmW x 54.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RØDE NT1Kit Cardioid Condenser Microphone w/SRM Combination Shock Mount & Dust Cover
$ 269.00 - Sold Out
RØDE NT1 Kit Cardioid Condenser Microphone with Shock Mount & Dust Cover.
RØDE SKU: NT1 Kit | Helix SKU: RMNT1Kit
Overview
The NT1 is a revolutionary new 1" diaphragm condenser microphone from RØDE.
Although the body of the new NT1 closely resembles the NT1-A, the microphone has been completely redesigned from the ground up, with the only shared component being the mesh grille.
RØDE’s design engineers approached the NT1 as a marriage of innovation and tradition, starting with the capsule which is a completely new design. Codenamed the HF6, it is the perfect example of RØDE’s fusion of artistic design approaches and cutting-edge manufacturing techniques, and features a sound signature reminiscent of the famous microphones of old while at the same time exhibiting extremely low noise.
It has been developed with a focus on detailed midrange response, coupled with silky smooth high frequencies, and warm, round, bass reproduction to make the NT1 an absolute standout in its class.
Specifications
| Operating Principle | Pressure Gradient |
| Transducer | Condenser |
| Diaphragm | 1" (25.40 mm) |
| Polar Pattern | Cardioid |
| Frequency Range | 20 Hz to 20 kHz |
| Equivalent Noise Level | 4 dB A-Weighted |
| Maximum SPL | 132 dB SPL 1% |
| Impedance | 100 ohms |
| Sensitivity | -29 dB, re: 1 V/Pa |
| Power Requirements | 24 V, 48 V |
| Output Connectors | 3-Pin XLR |
| Length | 7.36" (187 mm) |
| Diameter | 1.97" (50 mm) |
| Weight | 0.97 lb (440 g) |
Packaging Info
Package Weight 3.9 lb
Box Dimensions (LxWxH) 15.2 x 10.7 x 5.4"
RØDE NT2-A Studio Solution Package
$ 399.00 - Sold Out
RØDE NT2-A Studio Solution Package
RØDE SKU: NT2-A | Helix SKU: RMNT2A
Overview
Multi pattern 1" dual condenser microphone, featuring switchable omni, cardioid and figure 8 polar patterns, HPF and PAD.
- Large 1” HF1 gold sputtered capsule
- On body control of polar pattern, HPF and PAD
- Three position variable polar pattern - Omni, Cardioid or Figure 8
- Three position variable High-Pass Filter - Flat, 40Hz or 80Hz
- Three position PAD - 0dB, -5dB or -10dB
- Ultra low noise
- Internal capsule shock mounting
- Includes RØDE SM6 shock mount, pop filter and dust cover
- Designed and manufactured in Australia
- 10 year extended warranty when you register your microphone
The NT2-A carries on the tradition forged by the now legendary RØDE NT2. A professional large 1" capsule studio microphone incorporating three-position pick-up patterns, pad and high pass filter switches conveniently located on the mic body.
The frequency and transient response of this transducer has been voiced to complement today's modern recording techniques, and yet still evoke the silky smooth character of the legendary microphones of the 50s and 60s. These features provide the flexibility and superlative audio characteristics that make the NT2-A one of the most versatile condenser mics available.
Supplied with the SM6 shock mount, dust cover, microphone cable and DVD hosted by Grammy-nominated engineer and producer John Merchant showing a range of recording techniques specific to the NT2-A.
The RØDE NT2-A microphone is designed and made in Australia, and covered by RØDE's industry leading 10 year warranty.
Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter with bipolar output buffer |
| Capsule | 1.00" |
| Polar Pattern |
|
| Address Type | Side |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 200Ω |
| Maximum SPL | 147dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 16.0mV |
| Sensitivity | -36.0dB re 1 Volt/Pascal (16.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 7dB-A |
| Power Options |
|
| Weight | 860.00gm |
| Dimensions | 209.00mmH x 55.00mmW x 55.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RØDE NT2000 Variable Pattern Studio Condenser Microphone
$ 599.00 - Sold Out
RØDE NT2000 Variable Pattern Studio Condenser Microphone
RØDE SKU: NT2000 | Helix SKU: RMNT2000
Overview
Seamlessly variable dual 1" condenser microphone featuring continually variable polar pattern (omni through cardioid to figure 8), HPF and PAD.
- Large 1” HF1 gold sputtered capsule
- Continuously variable polar pattern, from Omni to Cardioid to Figure 8 controlled on the mic
- Continuously variable PAD and High-Pass Filter
- Ultra low noise, transformerless surface mount circuitry
- Wide dynamic range
- High strength welded and heat treated steel mesh head
- Internal capsule shock mounting
- Includes SM2 shock mount and RC1 case
- 10 year extended warranty when you register your microphone
The RØDE NT2000 microphone is a studio-quality large diaphragm condenser with seamlessly variable polar patterns. Its polar patterns selection, filter and pad are conveniently located on the front of the microphone body for ease of use.
Audiophile quality surface-mount electronics combined with a gold-sputtered dual 1" capsule provide extremely low self-noise (7dBA) and a maximum SPL of 147 dB (up to 157 dB with pad fully engaged) giving an incredible amount of versatility and ensuring exceptional results.
The RØDE NT2000 microphone is designed and made in Australia, and covered by RØDE's industry leading 10 year warranty.
Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter with bipolar output buffer |
| Capsule | 1.00" |
| Polar Pattern |
Figure 8 - picks up from the front and rear and rejects sides
|
| Address Type | Side |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 200Ω |
| Maximum SPL | 147dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 15.0mV |
| Sensitivity | -36.0dB re 1 Volt/Pascal (16.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 7dB-A |
| Power Options |
|
| Weight | 831.00gm |
| Dimensions | 208.00mmH x 55.00mmW x 55.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RØDE NTG2 Condenser Shotgun Microphone
$ 269.00
RØDE NTG2 Condenser Shotgun Microphone
Rode SKU: NTG2 | Helix SKU: RMNTG2
Overview
The RØDE NTG2 is a new, lightweight condenser shotgun microphone, designed for professional applications within the film, video, television, and production industries. The NTG2 provides a balanced low impedance output stage and operates either from an internal 1.5 V battery (AA) or 48 V phantom power. A wide bandwidth and controlled polar response coupled with low noise SMT electronics, makes the NTG2 the perfect choice for film, video engineering, and voice-over work. The NTG2 is extremely lightweight making it ideal for mounting directly to video cameras or on boom poles.
The NTG2 comes complete with zip pouch, stand mount, and windshield. The windscreen effectively suppresses wind noise when recording outdoors in moderate conditions.
- Broadcast sound quality
- Low noise circuitry
- 48V phantom power or 1.5V AA battery
- Two step high-pass filter - flat or 80 Hz
- Rugged metal construction
- Low weight - 161 grams (5 ounces)
- Low handling noise
- Supplied with stand mount, zip pouch, and windshield
Specifications
| Acoustic Principle | Line Gradient |
| Active Electronics | JFET impedance convertor with balanced transformer output |
| Capsule | 0.50" |
| Polar Pattern | |
| Address Type | End |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 250Ω |
| Maximum SPL | 131dBSPL |
| Maximum Output Level | 6.9mV (@ 1kHz, 1% THD into 1KΩ load) |
| Sensitivity | -36.0dB re 1 Volt/Pascal (15.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 18dBA |
| Power Options |
|
| Weight | 161.00g |
| Dimensions | 280.00mmH x 22.00mmW x 22.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
What's in the Box
|
NTG2 Multi-Powered Shotgun Microphone |
 |
RM5 Durable Microphone Clip |
 |
ZP2 Padded Zip Pouch (large) |
 |
WSVM Pop Filter/Wind Shield |
RØDE NTG4 Shotgun Microphone with Digital Switches & Rechargable Lithium Battery
$ 399.00 - Sold Out
RØDE NTG4 Shotgun Microphone with Digital Switches & Rechargable Lithium Battery
RØDE SKU: NTG4+ | Helix SKU: RMNTG4P
Overview
- Broadcast sound quality
- Low noise circuitry
- Rugged metal construction
- Convenient digital switching
- High Frequency Boost
- High Pass Filter (Flat/75Hz)
- PAD (-10db)
- 10 year extended warranty when you register your microphone
The NTG4 builds on the platform created by RØDE's award-winning NTG1 shotgun microphone. A broadcast-quality directional condenser microphone designed to provide premium audio recording in a versatile range of applications including on-camera and boom mounted.
Specifications
| Acoustic Principle | Line Gradient |
| Capsule | 0.50" |
| Polar Pattern | |
| Address Type | End |
| Frequency Range | 20Hz - 20kHz(selected HPF @75Hz) |
| Output Impedance | 200Ω |
| Maximum SPL | 135dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Sensitivity | -32.0dB re 1 Volt/Pascal (25.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 16dB-A |
| Power Options |
+12V phantom power required from mixer or interface
|
| Weight | 126gm |
| Dimensions | 225mmH x 22mmW x 22mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RØDELink NewsShooter Kit Digital Wireless System
$ 499.00 - Sold Out
RØDELink NewsShooter Kit Digital Wireless System
RØDE SKU: RODElink NewsShooter Kit | Helix SKU: RMRODElinkNewsshooter
Overview
RØDELink represents the next generation of digital wireless systems. Using a series II 2.4GHz digital transmission with 128-bit encryption, it is able to constantly monitor and hop between frequencies to maintain the strongest possible signal level at a range of up to 100 metres* (over 100 yards). The RØDELink Newsshooter Kit provides everything you need to start shooting video wirelessly with XLR microphones, including a camera-mounted receiver and an XLR transmitter. The receiver (RX-CAM) features an OLED display with information on level, battery status (receiver and transmitter), mute and channel selection. The unit can be mounted on a standard camera shoe mount, 3/8" thread or belt-clip, and for added versatility the shoe mount can be located in one of two positions. The transmitter (TX-XLR) easily connects to handheld presentation microphones as well as shotgun microphones, with a 3.5mm input and headphone output.
* range estimations based on optimal environment
RØDELink Newsshooter Kit Specifications:
| Transmission type | 2.4GHz Fixed Frequency Agile System |
| System dynamic range | 112dB |
| Range (distance) | Up To 100m |
| Frequency range | 35Hz - 22kHz |
| Maximum output level | 1v Rms (2.8v P-p) |
| Max input signal level | 1v Rms (2.8v P-p) |
| Max latency | 4ms |
| Power source | 2 X AA Battery Or MicroUSB |
| Antenna | Internal |
| Output connection | 3.5mm TRS Locking Jack Socket - Dual Mono |
| Output impedance | 300Ω |
| Dimensions | 111mm X 65mm X 52mm |
| Weight | 190gm |
| Power source | 2 X AA Battery, Sony NP-F Battery Or MicroUSB |
| Antenna | Internal |
| Input connection | XLR With Locking Collar, 3.5mm TRS Locking Jack Socket |
| Input impedance | 1kΩ (XLR), 10kΩ (3.5mm) |
| Dimensions | 120mm X 45mm X 45mm |
| Weight | 222gm |
RØDELink Wireless Filmmaker Kit
$ 399.00 - Sold Out
RØDELink Wireless Filmmaker Lavalier Kit
RØDE SKU: RODElink Film Maker Kit | Helix SKU: RMRODEFilmMakerKit
Overview
- Series II, 2.4GHz digital transmission
- 128-bit encryption
- Up to 100 metres range*
- OLED display (on receiver)
- One button pairing
- Three level gain control
- AA battery or USB powered
- Includes broadcast Lavalier microphone
- Two year extended warranty when you register your microphone
RØDELink represents the next generation of digital wireless systems. Using a series II 2.4GHz digital transmission with 128-bit encryption, it is able to constantly monitor and hop between frequencies to maintain the strongest possible signal level at a range of up to 100 metres* (over 100 yards). The RØDELink Filmmaker Kit provides everything you need to start shooting video wirelessly, including a receiver, transmitter and broadcast-grade lavalier microphone. The receiver (RX-CAM) features an OLED display with information on level, battery status (receiver and transmitter), mute and channel selection. The unit can be mounted on a standard camera shoe mount, 3/8" thread or belt-clip, and for added versatility the shoe mount can be located in one of two positions. The lightweight transmitter (TX-BELT) can be fitted to a belt or clothing and features a locking thread to ensure the microphone connection is as secure as possible. RØDE’s omnidirectional Lavalier microphone is included in the kit to provide the highest possible audio reproduction quality.
| Transmission type | 2.4GHz Fixed Frequency Agile System |
| System dynamic range | 112dB |
| Range (distance) | Up To 100m |
| Frequency range | 35Hz - 22kHz |
| Maximum output level | 1v Rms (2.8v P-p) |
| Max input signal level | 1v Rms (2.8v P-p) |
| Max latency | 4ms |
| Power source | 2 X AA Battery Or MicroUSB |
| Antenna | Internal |
| Input connection | 3.5mm TRS Locking Jack Socket - Dual Mono |
| Input impedance | 300Ω |
| Dimensions | 111mm X 65mm X 52mm |
| Weight | 190gm |
| Power source | 2 X AA Battery Or MicroUSB |
| Antenna | Internal |
| Input connection | 3.5mm TRS Locking Jack Socket |
| Input impedance | 10kΩ |
| Dimensions | 111mm X 65mm X 40mm |
| Weight | 190gm |
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter |
| Capsule | 0.10" |
| Address Type | End |
| Frequency Range | 60Hz - 18kHz |
| Output Impedance | 3000Ω |
| Maximum SPL | 110dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 189.0mV |
| Sensitivity | -33.5dB re 1 Volt/Pascal (21.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 25dB-A |
| Weight | 1.00gm |
| Dimensions | 12.00mmH x 4.50mmW x 4.50mmD |
Saramonic 2-Ch 3.5mm, XLR Microphone & 6.35mm Guitar Interface with Lightning Output Connector Professional Video, (SMARTRIG+DI)
$ 179.99
Saramonic 2-Ch 3.5mm, XLR Microphone & 6.35mm Guitar Interface with Lightning Output Connector Professional Video, (SMARTRIG+DI)
MFR SKU: SMARTRIG+DI | Helix SKU: SRSMARTRIGPDI
Overview
The SmartRig+ DI features three different kinds of inputs, and there are two of each: XLR, 1/4” (6.35mm), and 1/8“ (3.5mm). All of the inputs remain active when in use, and you can use 4 of them at the same time. The XLR inputs can supply condenser microphones with +48 volts of phantom power, which enables you to use almost any kind of microphone. The 1/4” (6.35mm) inputs are impedance-matched to get the best sound quality from guitars and basses. The 1/8“ (3.5mm) inputs can be used to connect 2 mini-plug microphones, which enables you to use microphones like the Saramonic SR-XLM1 clip-on lavalier mic, and the SR-M3 mini shotgun (both sold separately).
A Mono/Stereo switch on the SmartRig+ DI lets you choose how the channels will be mixed when connected to a device. When set to Mono, anything you plug in will be recorded to both channels. The Mono setting is useful when you’re just plugging in a single microphone, because the audio will be recorded to both channels. The Stereo setting is useful when you’re plugging two microphones or instruments, because both channels will be recorded as independent tracks. This gives you better editing options in post-production.
The multiple inputs on the SmartRig+ DI provide limitless creative potential. You can connect a guitar and microphone at the same time or plug in two microphones for music recording or podcasting. You can even connect the stereo outputs of a digital piano or synthesizer or attach a shotgun microphone and a wireless mic to vastly improve the sound quality of the videos you shoot. A built-in headphone jack lets you hear your music-making, audio recording, and video shooting apps, and two large gain knobs make it easy to set levels. The SmartRig+ DI is an affordable and ultra-portable device with impeccable sound quality that provides an impressive amount of functionality to a wide range of uses.
- High-quality 2-Channel Audio Interface for Apple iPhone, iPad, and iPod Touch
- Enables you to plug in 2 professional microphones or instruments to your Apple device in order to vastly improve the sound quality of videos you shoot, and the audio recorded with apps
- Ultra-compact, lightweight and easy to bring with you everywhere, included strap can be used to attach to selfie sticks, tripods, stands, stabilizers or belt, metal 1/4” 20 tripod thread on the back
- Two XLR inputs with +48v phantom power and 1/4” (6.35mm) instrument combo jacks and two 1/8“ (3.5mm) inputs, connect shotgun or lavalier microphones to improve sound for video
- Can be used to add a headphone jack to iPhones, 7 and newer
Specifications:
Frequency Response: 20Hz to 20kHz, +/-0.5dB
Distortion: Less than 0.01% @ 1kHz, -30dBu input
Signal to Noise Ratio: 80dB @ 1kHz, -30dBu input
Noise: -98dB full band (with Phantom Power)
Gain: +23dBu
Maximum Output Level: 2Vrms
Phantom Power: 48V
Phantom Max Current: 13mA
Channels: 2
Inputs: 2 x XLR + 1/4" (6.35mm) Combo Jack and 2 x 1.8” (3.5mm) TRS
Selectable Mixer: Mono or Stereo Output via Toggle Switch
Outputs: 1 x MFi Certified Lightning Output Cable and 1 x Female 1.8” (3.5 mm) Headphone Jack
Battery: 1 x 9-volt (Alkaline or Lithium)
Dimensions: 4.72" x 1.57" x 1.57" (120 x 40 x 40mm)
Weight: 4.6 oz (130g)
Saramonic 96-Channel Bodypack Transmitter Unit - TX9 (UwMic9 Lavalier Microphone)
$ 129.00 - Sold Out
Saramonic 96-Channel Bodypack Transmitter Unit - TX9 (UwMic9 Lavalier Microphone)
MFR SKU: UWMIC9TX9 | Helix SKU: SRUWMIC9TX9
Overview
The Saramonic TX9 is a wireless UHF bodypack transmitter and clip-on lavalier microphone bundle that provide stellar, broadcast-quality sound and are fully compatible with the dual-channel UwMic9 RX9 receiver (sold separately). The TX9 works right out of the box and is extremely easy to use. It’s ideal for DSLRs, video cameras or portable audio recorders for capturing interviews, film dialog, field recording, broadcast TV, news gathering, vlogging, YouTube videos and more. The TX9 features sturdy metal construction and delivers excellent sound quality in a low-cost package. It’s ultra-compact, lightweight, and easy to bring with you on every shoot.
The TX9 syncs with the RX9 receiver (sold separately) wirelessly through easy-to-use infrared sensors. The easy-to-read backlit LCD display lets you make quick adjustments to the intuitive menus in the brightest or darkest environments. The transmitter can be muted with the press of a button to give the person wearing it complete privacy, and the buttons can be “locked” when in use to prevent accidental muting or powering off.
This transmitter can be used with line-level audio, such as an output from a mixer. This can be useful at weddings and other events where you need to wirelessly transmit crystal-clear audio from a soundboard. The RF power output of the TX9 transmitter is also selectable. The “Low” setting lets you extend battery life in situations where the subject is close to the receiver. Medium and High are useful when the subject is going to be further away, or when you’re using the TX9 in an environment with more potential interference.
The included SR-M1 clip-on lavalier microphone features an omnidirectional pickup pattern that’sideal for use in video production because it captures sound equally no matter what direction it’s pointing when clipped to clothing.The microphone was designed to capture rich, crystal-clear sound and the transmitter features a locking BMP-type 1/8" (3.5mm) mic input to prevent the micfrom accidentally being unplugged. The UwMic9 TX9 is a high-quality transmitter with professional features, excellent sound quality, and an unbeatable budget-friendly price.
- Broadcast-quality UHF wireless beltpack transmitter and lavalier microphone for the RX9 dual receiver (sold separately)
- Works right out of the box with easy plug-and-play operation, lavalier mic, mic clip, foam windscreen, and belt clip are all included
- Professional SR-M1 omnidirectional lavalier microphone provides natural sound that’s ideal for video production
- Durable all-metal construction with easy-to-read backlit LCD display and easy-to-use menus and controls
- Offers up to 330-foot (100m) operating distance with infrared that makes it easy to sync channels with receiver
Specifications:
Wireless Frequency Range: 514 MHz - 596 MHz
Oscillator Type: PLL synthesizer
Input: Locking 1/8” (3.5mm) TRS mini-jack
Reference audio input level: –60 dBV (MIC input, 0 dB attenuation)
Antenna: 1/4 λwire antenna
Signal to Noise Ratio: 70 dB or more
Voice Delay: 12 ms
Reference Deviation: +/- 5 kHz (-60 dBV, 1 kHz input)
Frequency Response: 40 Hz to 18 kHz (+/- 3dB)
Distortion: 0.5% or less
Spur Suppression: -60 dB
Batteries: 2 LR6/AA size batteries
Dimensions: 6.73 x 2.5 x 1.18” (170.9 x 63.5 x 30.0mm)
Weight: 7.46 oz (211.4g) (without batteries)
In The Box:
1 x TX9 belt-pack transmitter
1 x SR-M1 omnidirectional lavalier mic
1 x Alligator-style lavalier mic clip
1 x Fitted foam windscreen
1 x Belt clip
1 x SR-UMBC1 battery compartment
1 x Printed user manual
1 x Warranty card
Optional Accessories (Sold Separately):
- LM-WS Fur Windjammer for SR-M1 Lavalier 3-Pack
- SR-LMWS3 Replacement Foam Windscreens 3-Pack
- WM4C-MC1 Replacement Mic Clip
- SR-UMBC1 Replacement Battery Compartment
- SR-XM1 Swiveling Omnidirectional Condenser Microphone
- SR-UM10-MC2 Replacement Belt Clip
- SR-UM10-M1 Replacement SR-M1 Lavalier
- SR-RX9 UwMic9 Dual-Channel Camera-Mountable Receiver
Saramonic Blink 500 B1 Tx+Rx 2.4GHz Micro-Wireless Lavalier System W/Camera-Mountable Dual-Receiver
$ 149.00 - Sold Out
Saramonic Blink 500 B1 Tx+Rx 2.4GHz Micro-Wireless Lavalier System W/Camera-Mountable Dual-Receiver
MFR SKU: BLINK500B1 | Helix SKU: SRBLINK500B1
Overview
If you want an extremely small, feather-weight wireless microphone system that delivers broadcast-quality sound to use with cameras and mobile devices, with the ability to handle two wireless transmitters, nothing is capable of doing this except for the Saramonic Blink 500. This kit comes with a single clip-on wireless transmitter with a built-in mic, a professional lavalier microphone, an ultracompact dual-channel receiver that mounts to the shoe of your camera with both TRS and TRRS output cables. You can put a mic on one person, but if you ever need to put mics on two people, you can simply add a second wireless transmitter (sold separately) and it will work perfectly with the included dual receiver.
Tiny body, huge sound.
The Blink 500 B1 is impossibly compact and lightweight, yet it delivers crystal-clear professional sound quality. The versatile transmitter features an excellent sounding built-in microphone that captures voices perfectly. Small enough to clip to a shirt or slide into a pocket and versatile enough to set on a table or podium, or even used handheld. It also operates as a traditional bodypack transmitter with the included SR-M1 professional omnidirectional clip-on lavalier microphone, providing an even more professional and visually discreet miking solution.
So advanced, it's effortless.
Some wireless microphone systems are complicated to operate and require detailed knowledge of their menus and settings, but the Blink 500 B1 is so technically advanced that it couldn't be easier to use. You just turn it on, and it works. But behind the scenes the Blink 500 is doing a lot to ensure excellent performance. It operates on the interference-free 2.4GHz spectrum, and automatically hops channels to avoid static noise and audio dropouts. Pairing the transmitter to the receiver is simple, and all of the complicated aspects of using wireless microphones happen seamlessly in the background, letting you concentrate on storytelling and getting a great shot.
Perfect levels and power.
One of the tricky aspects of capturing sound for video is controlling the audio levels. Some people speak very loudly, while others speak very softly. ThatÕs why Blink 500 transmitters have easy-to-use gain buttons to raise or lower the levels at the touch of a button, and an intelligent LED display shows you where they're set. The internal Lithium batteries get 5 hours of life from a charge with the included charging cables, and the USB-C ports can be used to power or recharge the units in the field with portable USB battery packs. The 10-milliwatt power of the transmitter gives you an impressive range of 98 feet (30 meters) with obstacles, and 164 feet (50 meters) in open spaces.
Loves cameras & mobile devices equally.
Both TRS and TRRS output cables are included so the system will work perfectly with DSLR, mirrorless, and other kinds of cameras, as well as smartphones and tablets that have headphone jacks. The output of the receiver provides a strong, noise-free level, so when you plug it in you can adjust the input level of your camera to its lowest setting to avoid hearing the noisy preamp of your camera.
An ideal wireless system.
Portable, compact wireless microphone systems are completely essential tools for anyone who shoots video, and the fact that the Blink 500 is one of the smallest and most lightweight systems you can ge yet it still delivers professional quality sound makes it ideal for filmmakers, journalists, vloggers, YouTube creators, corporate video producers, or any content creator that needs an incredibly easy-to-use wireless system that won't slow them down. It's small enough to tuck away into any camera bag, backpack or even your pocket, so you can effortlessly bring it with you everywhere you go. The Blink 500 B1 system is perfect for people who only need one wireless mic right now but may need the option to expand and use two in the future. Plus, the Blink 500 series is an evolving system of products that will soon be expanding, giving users even more options and versatility.
Specifications:
Transmitter Specifications:
Frequency: 2.4GHz
Oscillator Type: Gaussian Frequency-Shift Keying (GFSK)
RF Frequency Band: 2400 to 2483.5 MHz
RF Output Power: 10 mW
Signal to Noise Ratio: ≥70dB
Voice Delay: ≤6ms
Reference Audio Input Level: -30 to -42dBv (Microphone Input, 0 dB Attenuation)
Audio Gain Control: 11dB, 18dB, 25dB
Plug-In Power: Yes, 1V
Distortion: ≤0.1%
Digital Resolution: 24-bit / 48kHz
Frequency Response: 20Hz to 16kHz
Max Operating Range: 98.4’ (30m) with Obstacles, 164’ (50m) in Open Area
Max Number of Simultaneous Systems: 18 (up to 36 Microphones)
Antenna: Built-in 1/4λ Wire Antenna
Buttons: On / Off / Pair, Volume Up, Volume Down
Battery: Built-in Li-ion 3.7V / 400mAh
Approx. Battery Life: 5 hours
Charging Connector: USB Type-C (1.5 hours to be fully charged)
Input: 1/8'' (3.5mm) Microphone Input
Indicators: 4 x Blue LEDs: Indicates Power and Audio Level, 1 x Red LED: Indicates Low Battery Level, 1 x Green LED: Flashing when Charging / Off when Charge Finished
Microphone: Built-In Pressure Operated Electret Condenser
Microphone Pickup Pattern: Omnidirectional (Built-In Microphone and External Lavalier)
Microphone Frequency Range: 50Hz-18KHz (Built-In Microphone and External Lavalier)
Microphone Equivalent Noise Level: >58dB (Built-In Microphone and External Lavalier)
Maximum SPL: 120dB (Built-In Microphone), 110dB (External Lavalier)
Mounting Clip: Built-In
Operating Temperature: 0℃ to 50℃
Storage Temperature: -20℃ to +50℃
Dimensions: 2.5 x 1.7 x .65” (63 x 43 x 16.5mm)
Weight: 1.2 oz (34g)
Receiver Specifications:
Frequency: 2.4GHz
Oscillator type: Gaussian Frequency-Shift Keying (GFSK)
RF Frequency Band: 2400 to 2483.5 MHz
Signal to Noise Ratio: ≥70dB
Voice Delay: ≤6ms
Distortion: ≤0.1%
Digital Resolution: 24-bit / 48kHz
Frequency Response: 20Hz to 16kHz
Max Operating Range: 98.4’ (30m) with Obstacles, 164’ (50m) in Open Area
Antenna: Built-In 1/4λ Wire Antenna
Buttons: On / Off / Pair
Battery: Built-in Li-ion 3.7V / 400mAh
Approx. Battery Life: 5 hours
Charging Connector: USB Type-C
Output: 1/8' 3.5mm Jack (Headphone Compatible)
Audio Output Level: 5dB
Indicator: 1 LED, Blue. Flashing quickly: Paring, Flashing: Not Paired with any TX, Solid Blue: Paired with TX
Operating Temperature: 0℃ to 50℃
Storage Temperature: -20℃ to +50℃
Dimensions: 2.4 x 1.3 x .61” (62 x 33 x 15mm)
Weight: 1.09 oz (31g)
Saramonic Blink 500 B2 Ultracompact 2-Person Wireless Clip-On Mic System with Lavaliers & Dual Receiver
$ 199.00 - Sold Out
Saramonic Blink 500 B2 Ultracompact 2-Person Wireless Clip-On Mic System with Lavaliers & Dual Receiver
MFR SKU: BLINK500B2 | Helix SKU: SRBLINK500B2
Overview
If you want an extremely small, feather-weight wireless microphone system that delivers broadcast-quality sound to use with cameras and mobile devices, with the ability to handle two wireless transmitters so you can put mics on two separate people, nothing is capable of doing this except for the Saramonic Blink 500 B2. It comes with two clip-on wireless transmitters that have built-in mics, two professional lavalier microphones, and a dual-channel receiver that mounts to the shoe of your camera. You can put mics on two separate people, and it will work perfectly with the included ultracompact dual receiver.
Tiny body, huge sound.
The Blink 500 B2 is impossibly compact and lightweight, yet it delivers crystal-clear professional sound quality. The versatile transmitters feature excellent sounding built-in microphones that capture voices perfectly. Small enough to clip to a shirt or slide into a pocket and versatile enough to set on a table or podium, or even used handheld. They also operate as traditional bodypack transmitters with the included SR-M1 professional omnidirectional clip-on lavalier microphones, providing even more professional and inconspicuous miking solutions.
So advanced it's effortless.
Some wireless microphone systems are complicated to operate and require detailed knowledge of their menus and settings, but the Blink 500 B2 is so technically advanced that it couldn't be easier to use. You just turn it on, and it works. But behind the scenes the Blink 500 is doing a lot to ensure excellent performance. It operates on the interference-free 2.4GHz spectrum, and automatically hops channels to avoid static noise and audio dropouts. Pairing the transmitters with the receiver is simple, and all of the complicated aspects of using wireless microphones happen seamlessly in the background, letting you concentrate on storytelling and getting a great shot.
Perfect levels and power.
One of the tricky aspects of capturing sound for video is controlling the audio levels. Some people speak very loudly, while others speak very softly. That's why Blink 500 transmitters have easy-to-use gain buttons to raise or lower the levels at the touch of a button, and intelligent LED displays that show you where they're set. The internal Lithium batteries get 5 hours of life from a charge with the included charging cables, and the USB-C ports can be used to power or recharge the units in the field with portable USB battery packs. The 10-milliwatt power of the transmitters gives you an impressive range of 98 feet (30 meters) with obstacles, and 164 feet (50 meters) in open spaces.
Loves cameras & mobile devices equally.
Both TRS and TRRS output cables are included so the system will work perfectly with DSLR, mirrorless, and other kinds of cameras, as well as smartphones and tablets that have headphone jacks. The output of the receiver provides a strong, noise-free level, so when you plug it in you can adjust the input level of your camera to its lowest setting to avoid hearing the noisy preamp of your camera.
An ideal wireless system.
Portable, compact wireless microphone systems are completely essential tools for anyone who shoots video, and the fact that the Blink 500 is one of the smallest and most lightweight systems you can get yet it still delivers professional quality sound makes it ideal for filmmakers, journalists, vloggers, YouTube creators, corporate video producers, or any content creator that needs an incredibly easy-to-use 2-person wireless system that won't slow them down. It's small enough to tuck away into any camera bag, backpack or even your pocket, so you can effortlessly bring it with you everywhere you go. Plus, the Blink 500 series is an evolving system of products that will soon be expanding, giving users even more options and versatility.
Specifications:
Transmitter Specifications:
Frequency: 2.4GHz
Oscillator Type: Gaussian Frequency-Shift Keying (GFSK)
RF Frequency Band: 2400 to 2483.5 MHz
RF Output Power: 10 mW
Signal to Noise Ratio: ≥70dB
Voice Delay: ≤6ms
Reference Audio Input Level: -30 to -42dBv (Microphone Input, 0 dB Attenuation)
Audio Gain Control: 11dB, 18dB, 25dB
Plug-In Power: Yes, 1V
Distortion: ≤0.1%
Digital Resolution: 24-bit / 48kHz
Frequency Response: 20Hz to 16kHz
Max Operating Range: 98.4’ (30m) with Obstacles, 164’ (50m) in Open Area
Max Number of Simultaneous Systems: 18 (up to 36 Microphones)
Antenna: Built-in 1/4λ Wire Antenna
Buttons: On / Off / Pair, Volume Up, Volume Down
Battery: Built-in Li-ion 3.7V / 400mAh
Approx. Battery Life: 5 hours
Charging Connector: USB Type-C (1.5 hours to be fully charged)
Input: 1/8'' (3.5mm) Microphone Input
Indicators: 4 x Blue LEDs: Indicates Power and Audio Level, 1 x Red LED: Indicates Low Battery Level, 1 x Green LED: Flashing when Charging / Off when Charge Finished
Microphone: Built-In Pressure Operated Electret Condenser
Microphone Pickup Pattern: Omnidirectional (Built-In Microphone and External Lavalier)
Microphone Frequency Range: 50Hz-18KHz (Built-In Microphone and External Lavalier)
Microphone Equivalent Noise Level: >58dB (Built-In Microphone and External Lavalier)
Maximum SPL: 120dB (Built-In Microphone), 110dB (External Lavalier)
Mounting Clip: Built-In
Operating Temperature: 0℃ to 50℃
Storage Temperature: -20℃ to +50℃
Dimensions: 2.5 x 1.7 x .65” (63 x 43 x 16.5mm)
Weight: 1.2 oz (34g)
Receiver Specifications:
Frequency: 2.4GHz
Oscillator type: Gaussian Frequency-Shift Keying (GFSK)
RF Frequency Band: 2400 to 2483.5 MHz
Signal to Noise Ratio: ≥70dB
Voice Delay: ≤6ms
Distortion: ≤0.1%
Digital Resolution: 24-bit / 48kHz
Frequency Response: 20Hz to 16kHz
Max Operating Range: 98.4’ (30m) with Obstacles, 164’ (50m) in Open Area
Antenna: Built-In 1/4λ Wire Antenna
Buttons: On / Off / Pair
Battery: Built-in Li-ion 3.7V / 400mAh
Approx. Battery Life: 5 hours
Charging Connector: USB Type-C
Output: 1/8' 3.5mm Jack (Headphone Compatible)
Audio Output Level: 5dB
Indicator: 1 LED, Blue. Flashing quickly: Paring, Flashing: Not Paired with any TX, Solid Blue: Paired with TX
Operating Temperature: 0℃ to 50℃
Storage Temperature: -20℃ to +50℃
Dimensions: 2.4 x 1.3 x .61” (62 x 33 x 15mm)
Weight: 1.09 oz (31g)
Saramonic Blink 500 B3 Wireless Clip-On Mic System with Lavalier & Dual Lightning Receiver for iPhone & iPad
$ 169.00 - Sold Out
Saramonic Blink 500 B3 Wireless Clip-On Mic System with Lavalier & Dual Lightning Receiver for iPhone & iPad
MFR SKU: BLINK500B3 | Helix SKU: SRBLINK500B3
Overview
The Saramonic Blink 500 B3 is an incredibly compact, lightweight, and professional sounding wireless microphone systems for the Apple iPhone and iPad. The included clip-on transmitter is small enough to clip directly to your shirt collar, and the included RXDi MFi Certified Lighting dual-channel receiver is so lightweight and unobtrusive that it won't get in your way at all. It can easily be used on devices that are mounted in handheld gimbals, and the receiver is even capable of accepting the signal from two microphones if you add another Blink 500 TX transmitter (sold separately).
Tiny body, huge sound.
The Blink 500 B3 is impossibly compact and lightweight, yet it delivers crystal-clear professional sound quality. The versatile transmitter features an excellent sounding built-in microphone that captures voices perfectly. Small enough to clip to a shirt or slide into a pocket and versatile enough to set on a table or podium, or even used handheld. It also operates as a traditional bodypack transmitter with the included SR-M1 professional omnidirectional clip-on lavalier microphone, providing an even more professional and visually discreet miking solution. The sleek, featherweight RXDi receiver plugs directly into the Lightning port of your Apple device and doesn't require any batteries or charging to operate. There are no controls to fuss with, either. You just plug it in, and it works.
So advanced, it's effortless.
Some wireless microphone systems are complicated to operate and require detailed knowledge of their menus and settings, but the Blink 500 B3 is so technically advanced that it couldn't be easier to use. Even though there are no controls to adjust, behind the scenes the Blink 500 is doing a lot to ensure excellent performance. It operates on the interference-free 2.4GHz spectrum, and automatically hops channels to avoid static noise and audio dropouts. Pairing the transmitter to the receiver is simple, and all of the complicated aspects of using wireless microphones happen seamlessly in the background with the Blink 500, letting you concentrate on storytelling and getting a great shot.
Perfect levels and power.
One of the tricky aspects of capturing sound for video is controlling the audio levels. Some people speak very loudly, while others speak very softly. That's why Blink 500 transmitters have easy-to-use gain buttons to raise or lower the levels at the touch of a button, and an intelligent LED display shows you where they're set. The transmitter's internal Lithium battery gets 5 hours of life from a charge with the included charging cables, and the USB-C port can be used to power or recharge the transmitter in the field with portable USB battery packs. The 10-milliwatt power of the transmitter gives you an impressive range of 98 feet (30 meters) with obstacles, and 164 feet (50 meters) in open spaces.
Handheld gimbal, meet wireless sound.
Handheld gimbals have the amazing ability to deliver cinematically smooth video footage that makes it feel like the camera is floating, but one area where they suffer is audio. It's simply too difficult to attach external microphones or wireless receivers without throwing off the balance of the device. The RXDi receiver, included in your Blink 500 B3 kit changes this story. It's small and lightweight enough to remain mounted to your Apple device and won't interfere with the motors or arm of your gimbal. You can finally capture perfect sound with your mobile gimbal footage, and if you add a second Blink 500 TX transmitter (sold separately) you can easily put mics on two separate people.
An ideal wireless system.
Even if you shoot video with a mobile phone or tablet, wireless microphones are still completely essential tools for video production, and the fact that the Blink 500 is one of the smallest and most lightweight systems you can get yet it still delivers professional quality sound makes it ideal for filmmakers, journalists, vloggers, YouTube creators, corporate video producers, or any content creator that needs an incredibly easy-to-use wireless system that won't slow them down. This system is perfect for people who only need one wireless mic right now but may need the option to expand and use two in the future. If you shoot video with an iPhone and a handheld gimbal, this is the best solution available for perfect sound from wireless transmitters. It's small enough to tuck away in a small pocket, so you can effortlessly bring the Blink 500 with you everywhere you go. Plus, the Blink 500 series is an evolving system of products that will soon be expanding, giving users even more options and versatility.
Transmitter Specifications:
Frequency: 2.4GHz
Oscillator Type: Gaussian Frequency-Shift Keying (GFSK)
RF Frequency Band: 2400 to 2483.5 MHz
RF Output Power: 10 mW
Signal to Noise Ratio: ≥70dB
Voice Delay: ≤6ms
Reference Audio Input Level: -30 to -42dBv (Microphone Input, 0 dB Attenuation)
Audio Gain Control: 11dB, 18dB, 25dB
Plug-In Power: Yes, 1V
Distortion: ≤0.1%
Digital Resolution: 24-bit / 48kHz
Frequency Response: 20Hz to 16kHz
Max Operating Range: 98.4’ (30m) with Obstacles, 164’ (50m) in Open Area
Max Number of Simultaneous Systems: 18 (up to 36 Microphones)
Antenna: Built-in 1/4λ Wire Antenna
Buttons: On / Off / Pair, Volume Up, Volume Down
Battery: Built-in Li-ion 3.7V / 400mAh
Approx. Battery Life: 5 hours
Charging Connector: USB Type-C (1.5 hours to be fully charged)
Input: 1/8'' (3.5mm) Microphone Input
Indicators: 4 x Blue LEDs: Indicates Power and Audio Level, 1 x Red LED: Indicates Low Battery Level, 1 x Green LED: Flashing when Charging / Off when Charge Finished
Microphone: Built-In Pressure Operated Electret Condenser
Microphone Pickup Pattern: Omnidirectional (Built-In Microphone and External Lavalier)
Microphone Frequency Range: 50Hz-18KHz (Built-In Microphone and External Lavalier)
Microphone Equivalent Noise Level: >58dB (Built-In Microphone and External Lavalier)
Maximum SPL: 120dB (Built-In Microphone), 110dB (External Lavalier)
Mounting Clip: Built-In
Operating Temperature: 0℃ to 50℃
Storage Temperature: -20℃ to +50℃
Dimensions: 2.5 x 1.7 x .65” (63 x 43 x 16.5mm)
Weight: 1.2 oz (34g)
Receiver Specifications:
Frequency: 2.4GHz
Oscillator type: Gaussian Frequency-Shift Keying (GFSK)
RF Frequency Band: 2400 to 2483.5 MHz
Signal to Noise Ratio: ≥70dB
Voice Delay: ≤6ms
Distortion: ≤0.1%
Digital Resolution: 24-bit / 48kHz
Frequency Response: 20Hz to 16kHz
Max Operating Range: 98.4’ (30m) with Obstacles, 164’ (50m) in Open Area
Antenna: Built-in 1/4λ Wire Antenna
Connector: MFi Certified Lighting Apple Lightning Male
Button: Pairing Pinhole Button
Indicator: 1 LED, Blue. Flashing Quickly: Paring, Flashing: Not Paired with Any TX, Solid Blue: Paired with TX
Operating temperature: 0℃ to 50℃
Storage temperature: -20℃ to +50℃
Dimensions: 3 x 0.65 x 0.43” (76 x 16.5 x 11mm)
Weight: 0.35 oz (10g)
Saramonic Blink 500 B4 2-Person Wireless Clip-On Mic System with Lavalier & Lightning Receiver for iPhone & iPad
$ 219.00 - Sold Out
Saramonic Blink 500 B4 2-Person Wireless Clip-On Mic System with Lavalier & Lightning Receiver for iPhone & iPad
MFR SKU: BLINK500B4 | Helix SKU: SRBLINK500B4
Overview
The Saramonic Blink 500 B4 is an incredibly compact, lightweight, and professional sounding two-person wireless microphone system that was made for the Apple iPhone and iPad. The two included transmitters are small enough to clip directly to shirt collars, and the included RXDi MFi Certified Lighting receiver is so lightweight and unobtrusive that it can easily be used in handheld gimbals. The Blink 500 B4 makes using multiple wireless microphones with Apple devices as easy as possible and it provides broadcast-quality sound in a package that's amazingly compact and lightweight.
Tiny body, huge sound.
The versatile sub-compact wireless transmitters that come with the Blink 500 B4 have excellent sounding built-in microphones that capture voices perfectly. Small enough to clip to a shirt or slide into a pocket and versatile enough to set on a table or podium, or even used handheld. They also operate as traditional bodypack transmitters with the included SR-M1 omnidirectional clip-on lavalier microphones, providing an even more professional and inconspicuous miking solution. The impossibly compact RXDi dual-receiver plugs directly into the Lightning port of your Apple device and doesn't require any batteries or charging to operate. It doesn't have any controls to fuss with, either. You just plug it in, and it works.
So advanced, it's effortless.
Some wireless microphone systems are complicated to operate and require detailed knowledge of their menus and settings, but the Blink 500 B4 is so technically advanced that it couldn't be easier to use. Even though there are very few controls to adjust, behind the scenes the Blink 500 is doing a lot to ensure excellent performance. It operates on the interference-free 2.4GHz spectrum, and automatically hops channels to avoid static noise and audio dropouts. Pairing the transmitters to the receiver is simple, and all of the complicated aspects of using wireless microphones happen seamlessly in the background, letting you concentrate on storytelling and getting a great shot.
Perfect levels and power.
One of the tricky aspects of capturing sound for video is controlling the audio levels. Some people speak very loudly, while others speak very softly. That's why Blink 500 transmitters have easy-to-use gain buttons to raise or lower the levels at the touch of a button, and an intelligent LED display shows you where they're set. The internal Lithium batteries get 5 hours of life from a charge, and the USB-C charging ports can be used to power or recharge the transmitter in the field with portable USB battery packs. The 10-milliwatt power of the transmitter gives you an impressive range of 98 feet (30 meters) with obstacles, and 164 feet (50 meters) in open spaces.
Handheld gimbal, meet wireless sound.
Handheld gimbals have the amazing ability to deliver cinematically smooth video footage that makes it feel like the camera is floating, but one area where they suffer is audio. It's simply too difficult to attach external microphones or wireless receivers without throwing off the balance of the device. The RXDi receiver, included in your Blink 500 B4 kit changes this story. It's small and lightweight enough to remain mounted to your Apple device and won't interfere with the motors or arm of your gimbal. You can finally capture perfect sound with your mobile gimbal footage with the fantastic ability to put wireless mics on two separate people.
An ideal wireless system.
Even if you shoot video with a mobile phone or tablet, wireless microphones are still completely essential tools for video production, and the fact that the Blink 500 is one of the smallest and most lightweight systems you can get yet it still delivers professional quality sound makes it ideal for filmmakers, journalists, vloggers, YouTube creators, corporate video producers, or any content creator that needs an incredibly easy-to-use wireless system that won't slow them down. If you shoot video with an iPhone and a handheld gimbal, this is the best solution available for perfect sound from two wireless transmitters. This system is small enough to tuck away in a small pocket, so you can effortlessly bring the Blink 500 with you everywhere you go. Plus, the Blink 500 series is an evolving system of products that will soon be expanding, giving users even more options and versatility.
Transmitter Specifications:
Frequency: 2.4GHz
Oscillator Type: Gaussian Frequency-Shift Keying (GFSK)
RF Frequency Band: 2400 to 2483.5 MHz
RF Output Power: 10 mW
Signal to Noise Ratio: ≥70dB
Voice Delay: ≤6ms
Reference Audio Input Level: -30 to -42dBv (Microphone Input, 0 dB Attenuation)
Audio Gain Control: 11dB, 18dB, 25dB
Plug-In Power: Yes, 1V
Distortion: ≤0.1%
Digital Resolution: 24-bit / 48kHz
Frequency Response: 20Hz to 16kHz
Max Operating Range: 98.4’ (30m) with Obstacles, 164’ (50m) in Open Area
Max Number of Simultaneous Systems: 18 (up to 36 Microphones)
Antenna: Built-in 1/4λ Wire Antenna
Buttons: On / Off / Pair, Volume Up, Volume Down
Battery: Built-in Li-ion 3.7V / 400mAh
Approx. Battery Life: 5 hours
Charging Connector: USB Type-C (1.5 hours to be fully charged)
Input: 1/8'' (3.5mm) Microphone Input
Indicators: 4 x Blue LEDs: Indicates Power and Audio Level, 1 x Red LED: Indicates Low Battery Level, 1 x Green LED: Flashing when Charging / Off when Charge Finished
Microphone: Built-In Pressure Operated Electret Condenser
Microphone Pickup Pattern: Omnidirectional (Built-In Microphone and External Lavalier)
Microphone Frequency Range: 50Hz-18KHz (Built-In Microphone and External Lavalier)
Microphone Equivalent Noise Level: >58dB (Built-In Microphone and External Lavalier)
Maximum SPL: 120dB (Built-In Microphone), 110dB (External Lavalier)
Mounting Clip: Built-In
Operating Temperature: 0℃ to 50℃
Storage Temperature: -20℃ to +50℃
Dimensions: 2.5 x 1.7 x .65” (63 x 43 x 16.5mm)
Weight: 1.2 oz (34g)
Receiver Specifications:
Frequency: 2.4GHz
Oscillator type: Gaussian Frequency-Shift Keying (GFSK)
RF Frequency Band: 2400 to 2483.5 MHz
Signal to Noise Ratio: ≥70dB
Voice Delay: ≤6ms
Distortion: ≤0.1%
Digital Resolution: 24-bit / 48kHz
Frequency Response: 20Hz to 16kHz
Max Operating Range: 98.4’ (30m) with Obstacles, 164’ (50m) in Open Area
Antenna: Built-in 1/4λ Wire Antenna
Connector: MFi Certified Lighting Apple Lightning Male
Button: Pairing Pinhole Button
Indicator: 1 LED, Blue. Flashing Quickly: Paring, Flashing: Not Paired with Any TX, Solid Blue: Paired with TX
Operating temperature: 0℃ to 50℃
Storage temperature: -20℃ to +50℃
Dimensions: 3 x 0.65 x 0.43” (76 x 16.5 x 11mm)
Weight: 0.35 oz (10g)
Saramonic Blink 500 B5 Wireless Clip-On Mic System with Lavalier & Dual USB-C Receiver for Android Devices & more
$ 169.00 - Sold Out
Saramonic Blink 500 B5 Wireless Clip-On Mic System with Lavalier & Dual USB-C Receiver for Android Devices & more
MFR SKU: BLINK500B5 | Helix SKU: SRBLINK500B5
Overview
The Saramonic Blink 500 B5 is an extremely compact, lightweight, and professional sounding wireless microphone system that was made to be used with mobile devices that have USB-C ports, like Android smartphones or tablets, computers, and more. This kit comes with a single wireless transmitter with a built-in mic, a professional clip-on lavalier microphone, and a dual-channel receiver that's so lightweight and unobtrusive it can easily be used in handheld gimbals. You can put a mic on 1 person, but if you ever need to put mics on 2 people, you can simply add a second wireless transmitter (sold separately) and it will work perfectly with the included dual receiver.
Tiny body, huge sound.
The Blink 500 B5 is impossibly compact and lightweight, yet it delivers crystal-clear professional sound quality. The versatile transmitter features an excellent sounding built-in microphone that captures voices perfectly. Small enough to clip to a shirt or slide into a pocket and versatile enough to set on a table or podium, or even used handheld. It also operates as a traditional bodypack transmitter with the included SR-M1 professional omnidirectional clip-on lavalier microphone, providing an even more professional and inconspicuous miking solution. The RXUC receiver plugs directly into the USB-C port of your device and doesn't require any batteries or charging to operate. It doesn't have any controls to fuss with, either. You just plug it in, and it works. It's compatible with a wide range of products that have USB-C ports, from Android smartphones and tablets to modern Apple Mac computers and Windows PCs, to Chromebooks and even the 2018 iPad Pro tablets.
So advanced, it's effortless.
Some wireless microphone systems are complicated to operate and require detailed knowledge of their menus and settings, but the Blink 500 B5 is so technically advanced that it couldn't be easier to use. Even though there are very few controls to adjust, behind the scenes the Blink 500 is doing a lot to ensure excellent performance. It operates on the interference-free 2.4GHz spectrum, and automatically hops channels to avoid static noise and audio dropouts. Pairing the transmitter to the receiver is simple, and all of the complicated aspects of using wireless microphones happen seamlessly in the background, letting you concentrate on storytelling and getting a great shot.
Perfect levels and power.
One of the tricky aspects of capturing sound for video is controlling the audio levels. Some people speak very loudly, while others speak very softly. That's why the Blink 500 transmitter has easy-to-use gain buttons to raise or lower the levels, and an intelligent LED display shows you where they're set. Its internal Lithium battery gets 5 hours of life from a charge, and its USB-C charging port can be used to power or recharge it in the field with portable USB battery packs. The 10-milliwatt power of the transmitter gives you an impressive range of 98 feet (30 meters) with obstacles, and 164 feet (50 meters) in open spaces.
Handheld gimbal, meet wireless sound.
Handheld gimbals have the amazing ability to deliver cinematically smooth video footage that makes it feel like the camera is floating, but one area where they suffer is audio. It's simply too difficult to attach external microphones or wireless receivers without throwing off the balance of the device. The RXUC included in your Blink 500 B5 kit changes this story. It's small and lightweight enough to remain mounted to your smartphone and won't interfere with the motors or arm of your gimbal. You can finally capture perfect sound with your mobile gimbal footage, and if you add a second Blink 500 transmitter (sold separately) you can easily put mics on two people.
An ideal wireless system.
Even if you shoot video with a mobile phone or tablet, wireless microphones are still completely essential tools for video production, and the fact that the Blink 500 is one of the smallest and most lightweight systems you can get yet it still delivers professional quality sound makes it ideal for filmmakers, journalists, vloggers, YouTube creators, corporate video producers, or any content creator that needs an incredibly easy-to-use wireless system that won't slow them down. This system is perfect for people who only need one wireless mic right now but may need the option to expand and use two in the future. If you shoot video with a mobile device and a handheld gimbal, this is the best solution available for perfect sound from wireless transmitters. It's small enough to tuck away in a small pocket, so you can effortlessly bring it with you everywhere you go. Plus, the Blink 500 series is an evolving system of products that will soon be expanding, giving users even more options and versatility.
Transmitter Specifications:
Frequency: 2.4GHz
Oscillator Type: Gaussian Frequency-Shift Keying (GFSK)
RF Frequency Band: 2400 to 2483.5 MHz
RF Output Power: 10 mW
Signal to Noise Ratio: ≥70dB
Voice Delay: ≤6ms
Reference Audio Input Level: -30 to -42dBv (Microphone Input, 0 dB Attenuation)
Audio Gain Control: 11dB, 18dB, 25dB
Plug-In Power: Yes, 1V
Distortion: ≤0.1%
Digital Resolution: 24-bit / 48kHz
Frequency Response: 20Hz to 16kHz
Max Operating Range: 98.4’ (30m) with Obstacles, 164’ (50m) in Open Area
Max Number of Simultaneous Systems: 18 (up to 36 Microphones)
Antenna: Built-in 1/4λ Wire Antenna
Buttons: On / Off / Pair, Volume Up, Volume Down
Battery: Built-in Li-ion 3.7V / 400mAh
Approx. Battery Life: 5 hours
Charging Connector: USB Type-C (1.5 hours to be fully charged)
Input: 1/8'' (3.5mm) Microphone Input
Indicators: 4 x Blue LEDs: Indicates Power and Audio Level, 1 x Red LED: Indicates Low Battery Level, 1 x Green LED: Flashing when Charging / Off when Charge Finished
Microphone: Built-In Pressure Operated Electret Condenser
Microphone Pickup Pattern: Omnidirectional (Built-In Microphone and External Lavalier)
Microphone Frequency Range: 50Hz-18KHz (Built-In Microphone and External Lavalier)
Microphone Equivalent Noise Level: >58dB (Built-In Microphone and External Lavalier)
Maximum SPL: 120dB (Built-In Microphone), 110dB (External Lavalier)
Mounting Clip: Built-In
Operating Temperature: 0℃ to 50℃
Storage Temperature: -20℃ to +50℃
Dimensions: 2.5 x 1.7 x .65” (63 x 43 x 16.5mm)
Weight: 1.2 oz (34g)
Receiver Specifications:
Frequency: 2.4GHz
Oscillator type: Gaussian Frequency-Shift Keying (GFSK)
RF Frequency Band: 2400 to 2483.5 MHz
Signal to Noise Ratio: ≥70dB
Voice Delay: ≤6ms
Distortion: ≤0.1%
Digital Resolution: 24-bit / 48kHz
Frequency Response: 20Hz to 16kHz
Max Operating Range: 98.4’ (30m) with Obstacles, 164’ (50m) in Open Area
Antenna: Built-in 1/4λ Wire Antenna
Connector: USB-C Male
Button: Pairing Pinhole Button
Indicator: 1 LED, Blue. Flashing Quickly: Paring, Flashing: Not Paired with Any TX, Solid Blue: Paired with TX
Operating temperature: 0℃ to 50℃
Storage temperature: -20℃ to +50℃
Dimensions: 3 x 0.65 x 0.43” (76 x 16.5 x 11mm)
Weight: 0.35 oz (10g)
Saramonic Blink 500 B6 2-Person Wireless Clip-On Mic System with Lavalier & USB-C Receiver for Android Devices & more
$ 219.00 - Sold Out
Saramonic Blink 500 B6 2-Person Wireless Clip-On Mic System with Lavalier & USB-C Receiver for Android Devices & more
MFR SKU: BLINK500B6 | Helix SKU: SRBLINK500B6
Overview
The Saramonic Blink 500 B6 is an incredibly compact, lightweight, and professional sounding two-person wireless microphone system that was made to be used with mobile devices that have USB-C ports, like Android smartphones or tablets, computers, and more. The two included transmitters are small enough to clip directly to shirt collars, and the included RXUC receiver is so lightweight and unobtrusive that it can easily be used in handheld gimbals. The Blink 500 B6 makes using multiple wireless microphones as easy as possible and it provides broadcast-quality sound in a package that's incredibly compact and lightweight.
Tiny body, huge sound.
The versatile sub-compact wireless transmitters that come with the Blink 500 B6 have excellent sounding built-in microphones that capture voices perfectly. Small enough to clip to a shirt or slide into a pocket and versatile enough to set on a table or podium, or even used handheld. They also operate as traditional bodypack transmitters with the included SR-M1 omnidirectional clip-on lavalier microphones, providing an even more professional and inconspicuous miking solution. The impossibly compact RXUC dual-receiver plugs directly into the USB-C port of your device and it doesn't require any batteries or charging to operate. There are no controls to fuss with, either. You just plug it in, and it works.
So advanced, it's effortless.
Some wireless microphone systems are complicated to operate and require detailed knowledge of their menus and settings, but the Blink 500 B6 is so technically advanced that it couldn't be easier to use. Even though there are very few controls to adjust, behind the scenes the Blink 500 is doing a lot to ensure excellent performance. It operates on the interference-free 2.4GHz spectrum, and automatically hops channels to avoid static noise and audio dropouts. Pairing the transmitters to the receiver is simple, and all of the complicated aspects of using wireless microphones happen seamlessly in the background, letting you concentrate on storytelling and getting a great shot.
Perfect levels and power.
One of the tricky aspects of capturing sound for video is controlling the audio levels. Some people speak very loudly, while others speak very softly. That's why Blink 500 transmitters have easy-to-use gain buttons to raise or lower the levels at the touch of a button, and an intelligent LED display shows you where they're set. The internal Lithium batteries get 5 hours of life from a charge, and the USB-C charging ports can be used to power or recharge the transmitter in the field with portable USB battery packs. The 10-milliwatt power of the transmitter gives you an impressive range of 98 feet (30 meters) with obstacles, and 164 feet (50 meters) in open spaces.
Handheld gimbal, meet wireless sound.
Handheld gimbals have the amazing ability to deliver cinematically smooth video footage that makes it feel like the camera is floating, but one area where they suffer is audio. It's simply too difficult to attach external microphones or wireless receivers without throwing off the balance of the device. The RXUC included in your Blink 500 B6 kit changes this story. It's small and lightweight enough to remain mounted to your device and won't interfere with the motors or arm of your gimbal. You can finally capture perfect sound with your mobile gimbal footage with the fantastic ability to put wireless mics on two separate people.
An ideal wireless system.
Even if you shoot video with a mobile phone or tablet, wireless microphones are still completely essential tools for video production, and the fact that the Blink 500 is one of the smallest and most lightweight systems you can get yet it still delivers professional quality sound makes it ideal for filmmakers, journalists, vloggers, YouTube creators, corporate video producers, or any content creator that needs an incredibly easy-to-use wireless system that won't slow them down. If you shoot video with a mobile device and a handheld gimbal, this is the best solution available for perfect sound from wireless transmitters. This system is small enough to tuck away in a small pocket, so you can effortlessly bring it with you everywhere you go. Plus, the Blink 500 series is an evolving system of products that will soon be expanding, giving users even more options and versatility.
Transmitter Specifications:
Frequency: 2.4GHz
Oscillator Type: Gaussian Frequency-Shift Keying (GFSK)
RF Frequency Band: 2400 to 2483.5 MHz
RF Output Power: 10 mW
Signal to Noise Ratio: ≥70dB
Voice Delay: ≤6ms
Reference Audio Input Level: -30 to -42dBv (Microphone Input, 0 dB Attenuation)
Audio Gain Control: 11dB, 18dB, 25dB
Plug-In Power: Yes, 1V
Distortion: ≤0.1%
Digital Resolution: 24-bit / 48kHz
Frequency Response: 20Hz to 16kHz
Max Operating Range: 98.4’ (30m) with Obstacles, 164’ (50m) in Open Area
Max Number of Simultaneous Systems: 18 (up to 36 Microphones)
Antenna: Built-in 1/4λ Wire Antenna
Buttons: On / Off / Pair, Volume Up, Volume Down
Battery: Built-in Li-ion 3.7V / 400mAh
Approx. Battery Life: 5 hours
Charging Connector: USB Type-C (1.5 hours to be fully charged)
Input: 1/8'' (3.5mm) Microphone Input
Indicators: 4 x Blue LEDs: Indicates Power and Audio Level, 1 x Red LED: Indicates Low Battery Level, 1 x Green LED: Flashing when Charging / Off when Charge Finished
Microphone: Built-In Pressure Operated Electret Condenser
Microphone Pickup Pattern: Omnidirectional (Built-In Microphone and External Lavalier)
Microphone Frequency Range: 50Hz-18KHz (Built-In Microphone and External Lavalier)
Microphone Equivalent Noise Level: >58dB (Built-In Microphone and External Lavalier)
Maximum SPL: 120dB (Built-In Microphone), 110dB (External Lavalier)
Mounting Clip: Built-In
Operating Temperature: 0℃ to 50℃
Storage Temperature: -20℃ to +50℃
Dimensions: 2.5 x 1.7 x .65” (63 x 43 x 16.5mm)
Weight: 1.2 oz (34g)
Receiver Specifications:
Frequency: 2.4GHz
Oscillator type: Gaussian Frequency-Shift Keying (GFSK)
RF Frequency Band: 2400 to 2483.5 MHz
Signal to Noise Ratio: ≥70dB
Voice Delay: ≤6ms
Distortion: ≤0.1%
Digital Resolution: 24-bit / 48kHz
Frequency Response: 20Hz to 16kHz
Max Operating Range: 98.4’ (30m) with Obstacles, 164’ (50m) in Open Area
Antenna: Built-in 1/4λ Wire Antenna
Connector: USB-C Male
Button: Pairing Pinhole Button
Indicator: 1 LED, Blue. Flashing Quickly: Paring, Flashing: Not Paired with Any TX, Solid Blue: Paired with TX
Operating temperature: 0℃ to 50℃
Storage temperature: -20℃ to +50℃
Dimensions: 3 x 0.65 x 0.43” (76 x 16.5 x 11mm)
Weight: 0.35 oz (10g)
Saramonic Blink 500 RXDi Dual-Channel Lightning Wireless Microphone Receiver for iPhone and iPad
$ 89.00 - Sold Out
Saramonic Blink 500 RXDi Dual-Channel Lightning Wireless Microphone Receiver for iPhone and iPad
MFR SKU: BLINK500RXDI | Helix SKU: SRBLINK500RXDI
Overview
The Saramonic Blink 500 RXDi is an incredibly compact, lightweight, and professional sounding wireless dual-receiver that was made for the Apple iPhone and iPad. It's so lightweight and unobtrusive that it can easily be used in handheld gimbals and can handle up to two separate Blink 500 TX wireless transmitters (sold separately). The RXDi makes using multiple wireless microphones with Apple devices as easy as possible. It connects directly to the Lightning port, and no batteries or charging is required. The RXDi provides broadcast-quality sound in an incredibly compact and lightweight package.
So advanced, it's effortless.
Some wireless microphone receivers are complicated to operate, but the Blink 500 RXDi is so technically advanced that it couldn't be easier to use. There are no controls to adjust, but the device does a lot behind the scenes to ensure excellent performance. It operates on the interference-free 2.4GHz spectrum, and automatically hops channels to avoid static noise and audio dropouts. Pairing with transmitters is simple, and all of the complicated aspects of using wireless microphones happen seamlessly in the background, letting you concentrate on storytelling and getting a great shot.
Handheld gimbal, meet wireless sound.
Handheld gimbals have the amazing ability to deliver cinematically smooth video footage that makes it feel like the camera is floating, but one area where they suffer is audio. It's simply too difficult to attach external microphones or wireless receivers without throwing off the balance of the device. The RXDi changes this story. It's small and lightweight enough to remain mounted to your Apple device and won't interfere with the motors or arm of your gimbal. You can finally capture perfect sound with your mobile gimbal footage when used with Blink 500 TX transmitters (sold separately).
Blink 500: a diverse ecosystem.
There's a large family of innovative Blink 500 wireless microphone products and they're are all ultra-compact, lightweight, and fully compatible with the Blink 500 RXDi. The Blink 500 TX is a tiny wireless transmitter with a high-quality built-in microphone, an external mic input (it comes with an external lavalier mic), a built-in Lithium battery, a USB-C charging port, gain buttons and multicolored LEDs. The Blink 500 RX is a dual-receiver that was designed to be mounted to the shoe of a camera and can handle up to two 500 TX transmitters at the same time. The Blink 500 RXUC is very similar to the RXDi except it has a USB-C connector for Android smartphones or tablets and modern Apple Mac and PC computers. It works perfectly with handheld gimbals, too. All of the receivers can handle up to two Blink 500 TX transmitters at the same time.
An ideal wireless system.
Even if you shoot video with a smartphone or tablet, wireless microphones are still completely essential tools for video production, and the fact that the Blink 500 is one of the smallest and most lightweight systems you can get yet it still delivers professional quality sound makes it ideal for filmmakers, journalists, vloggers, YouTube creators, corporate video producers, or any content creator that needs an incredibly easy-to-use wireless system that won't slow them down. If you shoot video with an iPhone and a handheld gimbal, the Blink 500 RXDi is the best solution available for perfect sound from up to two wireless transmitters (sold separately). The RXDi is small enough to tuck away in a small pocket, so you can effortlessly bring it with you everywhere you go. Plus, the Blink 500 series is an evolving system of products that will soon be expanding, giving users even more options and versatility.
Specifications:
Frequency: 2.4GHz
Oscillator type: Gaussian Frequency-Shift Keying (GFSK)
RF Frequency Band: 2400 to 2483.5 MHz
Signal to Noise Ratio: ≥70dB
Voice Delay: ≤6ms
Distortion: ≤0.1%
Digital Resolution: 24-bit / 48kHz
Frequency Response: 20Hz to 16kHz
Max Operating Range: 98.4’ (30m) with Obstacles, 164’ (50m) in Open Area
Antenna: Built-in 1/4λ Wire Antenna
Connector: MFi Certified Lighting Apple Lightning Male
Button: Pairing Pinhole Button
Indicator: 1 LED, Blue. Flashing Quickly: Paring, Flashing: Not Paired with Any TX, Solid Blue: Paired with TX
Operating temperature: 0℃ to 50℃
Storage temperature: -20℃ to +50℃
Dimensions: 3 x 0.65 x 0.43” (76 x 16.5 x 11mm)
Weight: 0.35 oz (10g)
Saramonic Blink 500 RXUC Dual-Channel USB-C Wireless Microphone Receiver for Android Mobile Devices & More
$ 89.00 - Sold Out
Saramonic Blink 500 RXUC Dual-Channel USB-C Wireless Microphone Receiver for Android Mobile Devices & More
MFR SKU: BLINK500RXUC | Helix SKU: SRBLINK500RXUC
Overview
The Saramonic Blink 500 RXUC is an incredibly compact, lightweight, and professional sounding wireless dual-receiver that was made for devices with USB-C ports. It's compatible with a wide range of products, from Android smartphones and tablets to modern Apple Mac computers and Windows PCs, to Chromebooks and even 2018 iPad Pro tablets. It's so lightweight and unobtrusive that it can easily be used in handheld gimbals and can handle up to two separate Blink 500 TX wireless transmitters (sold separately). The RXUC makes using multiple wireless microphones as easy as possible. It connects directly to USB-C ports, so no batteries or charging is required. The RXUC provides broadcast-quality sound in an incredibly compact and lightweight package.
So advanced, it's effortless.
Some wireless microphone receivers are complicated to operate, but the Blink 500 RXUC is so technically advanced that it couldn't be easier to use. There are no controls to adjust, but the device does a lot behind the scenes to ensure excellent performance. It operates on the interference-free 2.4GHz spectrum, and automatically hops channels to avoid static noise and audio dropouts. Pairing with transmitters is simple, and all of the complicated aspects of using wireless microphones happen seamlessly in the background, letting you concentrate on storytelling and getting a great shot.
Handheld gimbal, meet wireless sound.
Handheld gimbals have the amazing ability to deliver cinematically smooth video footage that makes it feel like the camera is floating, but one area where they suffer is audio. It's simply too difficult to attach external microphones or wireless receivers without throwing off the balance of the device. The RXUC changes this story. It's small and lightweight enough to remain mounted to your mobile device and won't interfere with the motors or arm of your gimbal. You can finally capture perfect sound with your mobile gimbal footage when used with Blink 500 TX transmitters (sold separately).
Blink 500: a diverse ecosystem.
There's a large family of innovative Blink 500 wireless microphone products and they're are all ultra-compact, lightweight, and fully compatible with the Blink 500 RXUC. The Blink 500 TX is a tiny wireless transmitter with a high-quality built-in microphone, an external mic input (it comes with an external lavalier mic), a built-in Lithium battery, a USB-C charging port, gain buttons and multicolored LEDs. The Blink 500 RX is a dual-receiver that was designed to be mounted to the shoe of a camera and can handle up to two 500 TX transmitters at the same time. The Blink 500 RXDi is very similar to the RXUC except it has a Lightning connector for the Apple iPhones and iPad. It works perfectly with handheld gimbals, too. All of the receivers can handle up to two Blink 500 TX transmitters at the same time.
An ideal wireless system.
Even if you shoot video with a mobile phone or tablet, wireless microphones are still completely essential tools for video production, and the fact that the Blink 500 is one of the smallest and most lightweight systems you can get yet it still delivers professional quality sound makes it ideal for filmmakers, journalists, vloggers, YouTube creators, corporate video producers, or any content creator that needs an incredibly easy-to-use wireless system that won't slow them down. If you shoot video with an Android smartphone and a handheld gimbal, the Blink 500 RXUC is the best solution available for perfect sound from up to two wireless transmitters (sold separately). The RXUC is small enough to tuck away in a small pocket, so you can effortlessly bring it with you everywhere you go. Plus, the Blink 500 series is an evolving system of products that will soon be expanding, giving users even more options and versatility.
Specifications:
Frequency: 2.4GHz
Oscillator type: Gaussian Frequency-Shift Keying (GFSK)
RF Frequency Band: 2400 to 2483.5 MHz
Signal to Noise Ratio: ≥70dB
Voice Delay: ≤6ms
Distortion: ≤0.1%
Digital Resolution: 24-bit / 48kHz
Frequency Response: 20Hz to 16kHz
Max Operating Range: 98.4’ (30m) with Obstacles, 164’ (50m) in Open Area
Antenna: Built-in 1/4λ Wire Antenna
Connector: USB-C Male
Button: Pairing Pinhole Button
Indicator: 1 LED, Blue. Flashing Quickly: Paring, Flashing: Not Paired with Any TX, Solid Blue: Paired with TX
Operating temperature: 0℃ to 50℃
Storage temperature: -20℃ to +50℃
Dimensions: 3 x 0.65 x 0.43” (76 x 16.5 x 11mm)
Weight: 0.35 oz (10g)
Saramonic C-XLR 3.5mm Female TRS to XLR Male Audio Adapter for Professional Cameras, Mixers, Recorders and more
$ 10.00 - Sold Out
Saramonic C-XLR 3.5mm Female TRS to XLR Male Audio Adapter for Professional Cameras, Mixers, Recorders and more
MFR SKU: C-XLR | Helix SKU: SRCXLR
Overview
The Saramonic C-XLR is a versatile audio adapter that lets you easily connect microphones and audio sources that have 3.5mm male jacks into the XLR inputs on professional video and cinema cameras, audio recorders, mixers, and more. It's compatible with battery-powered, active or dynamic microphones, wireless receivers, 3.5mm line-level devices and more.
Tough and Lightweight Lifesaver
You need dependable, solidly built equipment and the C-XLR delivers with tough, all-brass construction and premium gold-plated connectors. The input is fully compatible with both regular or locking 3.5mm connectors and even is even threaded to conveniently secure locking connections. Whether you need to connect a battery-powered 3.5mm lavalier mic directly to a pro video camera, plug an active headset microphone into a sound system, use a battery-powered mini-plug shotgun microphone with a field mixer, connect a wireless receiver like the Saramonic Blink 500 (B1/B2) into a cinema camera, or connect a 3.5mm line signal to an PA mixer, the C-XLR will make it happen. It is an invaluable problem solver to have in your audio kit.
Specifications:
Adapter Type: 1/8“ (3.5mm) TRS Female to XLR Male
Input Compatibility: Standard and Locking 3.5mm Connectors
Dimensions: 0.9 x 3” (23 x 76.5mm)
Weight: 3.1oz (87.9g)
Saramonic C-XLR+ 3.5mm Female TRS to XLR Male Audio Adapter with Phantom Power to Plug-In-Power Converter for Pro Cameras, Mixers, Recorders and more
$ 20.00 - Sold Out
Saramonic C-XLR+ 3.5mm Female TRS to XLR Male Audio Adapter with Phantom Power to Plug-In-Power Converter for Pro Cameras, Mixers, Recorders and more
MFR SKU: C-XLR+ | Helix SKU: SRCXLRP
Overview
The Saramonic C-XLR+ is a useful audio adapter that lets you easily connect microphones and audio sources that have 3.5mm male jacks into the XLR inputs on professional video and cinema cameras, audio recorders, mixers, and more. It's compatible with active, battery-powered microphones and passive microphones, such as the lavalier mics that come with wireless systems. If you engage phantom power on the camera or other device, a built-in converter in the C-XLR+ changes the current from +48-volts to the 3 to 5-volt current that plug-in-powered and some passive 3.5mm microphones require. This happens automatically. There are no controls on the C-XLR+ that need your attention.
Tough and Lightweight Lifesaver
You need dependable, solidly built equipment and the C-XLR+ delivers with tough, all-brass construction and premium gold-plated connectors and even is even threaded to conveniently secure locking connections. The input is fully compatible with both regular and locking 3.5mm connectors. Whether you need to connect a 3.5mm lavalier mic directly to a pro video camera, plug a headset microphone into a sound system, use a plug-in-powered mini-plug shotgun microphone with a field mixer, connect a wireless receiver like the Saramonic Blink 500 (B1/B2) into a cinema camera, or connect a 3.5mm line signal to an PA mixer, the C-XLR+ will make it happen. It is an invaluable problem solver to have in your audio kit and can even expand the use of your 3.5mm plug-in-powered, or lavalier microphones into your professional devices.
Specifications:
Length: 3.94” (100mm)
Width: 2.76” (70mm)
Height: 2.76” (70mm)
Weight: 0.6 (17g)
Saramonic CamMic+ On-Camera Battery-Powered Shotgun Microphone for DSLR, Mirrorless & Video Cameras or Smartphones & Tablets
$ 99.00 - Sold Out
Saramonic CamMic+ On-Camera Battery-Powered Shotgun Microphone for DSLR, Mirrorless & Video Cameras or Smartphones & Tablets
MFR SKU: CAMMIC+ | Helix SKU: SRCAMMICP
Overview
The Saramonic CamMic+ is a lightweight yet durably built, AA-battery powered shotgun microphone that delivers clear, broadcast-quality sound to DSLR, mirrorless, video cameras and mobile devices. Its directional pickup pattern excels at capturing sounds in front of the mic, while rejecting sounds to the sides and rear. It’s a premium quality microphone with impressively quality construction at an affordable price that’s incredibly easy to use, and it can be used with a wide variety of cameras and mobile devices.
A stand out feature of the CamMic+ design is the unique microphone shockmount. The wiry shockmounts on some competing microphones are flimsy and prone to bending, this can cause some unwanted audio issues and change the way the microphone picks up sound. The integrated shockmount of CamMic+ is robust and features a sleek, sweeping and stable design.
A dual layered uniquely designed bullet like windscreen is included, giving the CamMic+ its unique and interesting look. It features a sturdy gasket which aids in blocking wind noise, helps to protect the microphone from things like weather and dust, and keeps it securely fastened in place while on the go.The output cable of the CamMic+ is removable. An 1/8" (3.5mm) TRS cable for connecting to cameras is included, in addition to a 1/8" (3.5mm) TRRS cable for connecting to smartphones and tablets. On the back of the mic there is a 3-position switch for OFF, ON, and an 80Hz high-pass filter that enables you to eliminate unwanted rumble sounds and make dialog more intelligible when shooting in noisy environments. A built-in camera shoe-mount features a metal 1/4 20 tripod thread at the base that gives you near limitless mounting options.
Powered by a single AA battery, the CamMic+ is the ideal choice for cameras that don’t provide plug-in power. Allowing you to shoot for days without replacing the battery. For those filmmakers worried about conserving as much camera/mobile device power as possible, the CamMic+ would be the mic of choice. There is also a Blue LED indicator light that will illuminate when the mic is on and turn red when your battery needs to be replaced.
- Provides clear, broadcast-quality sound to DSLR, Mirrorless and Video Cameras or Smartphones and Tablets
- AA Battery-powered for cameras that lack plug-in-power or to save camera battery life
- Easy-to-use with plug-and-play operation. Includes two output cables: one for cameras, one for mobile devices
- Sleek camera-mountable design that is lightweight and compact, yet features an impressively solid construction
- Double thickness windscreen and low-cut filter improves intelligibility of dialog in any situation
Specifications:
Type: Condenser MicrophonePolar Pattern: Cardioid (Uni-Directional)
Frequency Range: 40Hz - 10kHz
Sensitivity: -45 ±3dB (0dB = 1V/Pa, @ 1kHz)
Maximum Input SPL: f=1kHz, THD<5% (106dB)
Output Impedance: 200ohm
Signal to Noise Ratio: 80dB SPL
Power Requirements: One AA Battery
Weight: 3.77oz (107g)
Dimensions: 6.47 x 2.12 x 3.29” (164.4 x 53.9 x 83.5mm)
Product Weight: 0.107kg
Product Length: 16.4cm
Product Width: 8.4cm
Product Height: 5.4cm
Package Weight: 0.327kg
Package Length: 30cm
Package Width: 13cm
Package Height: 7.5cm
1-Year Warranty
Saramonic CamMic-WS Slide-On Furry Windscreen for the Saramonic CamMic
$ 79.00
Saramonic CamMic-WS Slide-On Furry Windscreen for the Saramonic CamMic
MFR SKU: CAMMIC | Helix SKU: SRCAMMIC
Overview
The Saramonic CamMic-WS is a furry windscreen that is designed for higher outdoor wind conditions, when the foam windscreen just won’t do. Its long-haired exterior and nylon interior provides dual-layered wind protection. Drastically improving wind diffusion and reducing wind noise up to 40dB.
Designed for the Saramonic CamMic, it easily slips right over the CamMic’s foam windscreen. It is an ideal solution to get the best quality sound in high wind recording environments.
Specifications:
Length: 3.94” (100mm)
Width: 2.76” (70mm)
Height: 2.76” (70mm)
Weight: 0.6 (17g)
Saramonic CamMic-WS Slide-On Furry Windscreen for the Saramonic CamMic
$ 18.00 - Sold Out
Saramonic CamMic-WS Slide-On Furry Windscreen for the Saramonic CamMic
MFR SKU: CAMMICWS | Helix SKU: SRCAMMICWS
Overview
The Saramonic CamMic-WS is a furry windscreen that is designed for higher outdoor wind conditions, when the foam windscreen just won’t do. Its long-haired exterior and nylon interior provides dual-layered wind protection. Drastically improving wind diffusion and reducing wind noise up to 40dB.
Designed for the Saramonic CamMic, it easily slips right over the CamMic’s foam windscreen. It is an ideal solution to get the best quality sound in high wind recording environments.
Specifications:
Length: 3.94” (100mm)
Width: 2.76” (70mm)
Height: 2.76” (70mm)
Weight: 0.6 (17g)
Saramonic DK4B Miniature Professional Omnidirectional Lavalier Mic w/ Locking 3.5mm TRS Connector for Sony Wireless Transmitters
$ 125.00 - Sold Out
Saramonic DK4B Miniature Professional Omnidirectional Lavalier Mic w/ Locking 3.5mm TRS Connector for Sony Wireless Transmitters
Mfr SKU: DK4B | Helix SKU: SRDK4B
Overview
| The Saramonic DK4B is a premium broadcast lavalier microphone for wireless systems that will greatly enhance the sound quality of your productions with its truly excellent sonic performance. Its omnidirectional polar pattern provides 360-degrees of sound pickup and is ideal for capturing natural sounding dialog for video productions, interviews, speech and many other applications and perfect for acoustic instruments. Deigned with a flat, low-profile form factor and a premium, professional look. It is visually unobtrusive and looks great on camera when exposed and easily is concealed. Perfect for taping under clothing and hiding in hair or on costumes. Wide and Warm Sound The DK4 lavalier is specially designed to enhance the character of dialog and capture the detailed subtleties of musical instruments. It delivers a crisp, full-frequency response with refined, smooth sound and warmth of tone. It features a wide pick-up response, both direct and off-axis from the microphone capsule, enhancing sensitivity and minimizing unwanted noise. Perfect Sound Anywhere It doesn’t matter if you’re using the DK4 indoors in a quiet room or outside in a storm—you’re always going to get perfect sound because every critically important windscreen accessory you need are all included. The microphone, clips and all four included windscreens all fit neatly into pockets in the included compact soft-shell case. Designed with Care It’s the little things that make a big difference in the quality of a product, and the DK4 is loaded with them. Good examples of this are the form-fitted, slide-in mic clips that keeps the DK4 securely in place, even when the cable is jerked on. And the elastic fastening clips on the furry windscreens, allowing you to wrap the windscreen closely to the mic for added protection from the wind, and to prevent it from falling off. For Sony Wireless The locking gold-plated 3.5mm connector is compatible with Sony UWP, UWP-D and WRT series wireless transmitters. |
Features
| Premium low-profile lavalier microphone for wireless and recorders designed for broadcast and instruments that delivers superior sound quality and advanced sonic performance |
| Tailored frequency response designed to enhance the character and intelligibility of speech, and detailed subtleties of musical instruments |
| Omnidirectional pickup pattern is ideal for capturing natural sounding dialog for broadcast video and audio productions |
| Premium included accessory suite includes: 2x foam windscreens, 2x furry high-wind windscreens, 2x alligator-style mic clips and a lightweight yet protective case |
| Locking 3.5mm connector compatible with Sony UWP, UWP-D and WRT series wireless system belt pack transmitters |
Specifications
Acoustic Principle: Electret Condenser
Polar Pattern: Omnidirectional
Sensitivity: -40±2dB RL=2.2KΩ Vs=2.0V( 1KHz 0dB=1V/Pa)
Frequency Range: 20Hz to 16kHz
Max Input SPL :105dB
Signal-to-Noise Ratio: 58dB or more
Output Impedance: Max. 2.2KΩ 1KHz (RL=2.2KΩ)
Operating Temperature: -20°C - 60°C
Connector: Gold-Plated Locking 3.5mm
Cable Length: 70.87” (180cm)
Weight: 0.49oz (14g)
Compatible Wireless Transmitters:
Sony: UWP, UWP-D and WRT Series Transmitters
Sony: PMC-A10, PMC-D10, PMC-D50, PMC-D100, PMC-D1
In The Box
1 x DK4B Low-Profile Omnidirectional Lavalier Microphone
2 x Fitted Slide-In Alligator-Style Mic Clip
2 x Foam Windscreens
2 x High-Wind Furry Windscreens with Elastic Fastening Clasps
1 x Reusable Cable Wrap
1 x Protective Soft-Shell Case with 2 Mesh Pockets
1 x Carabiner Clip
1 x Warranty Card
Saramonic LavMicro 2M Dual Lavalier Microphones for DSLRs, Mirrorless, Video Cameras, Smartphones, Tablets & more
$ 69.00 - Sold Out
Saramonic LavMicro 2M Dual Lavalier Microphones for DSLRs, Mirrorless, Video Cameras, Smartphones, Tablets & more
MFR SKU: LAVMICRO2M | Helix SKU: SRLAVMICRO2M
Overview
The Saramonic LavMicro 2M is a set of two high-quality clip-on wired lavalier microphones that share one cable and connect to a single 1/8“ (3.5mm) mic input. This enables you to put wired lavalier mics on two people and plug into a single mic input on a camera or an audio recorder. The microphones deliver broadcast-quality sound to DSLRs, mirrorless, cinema, and video cameras, as well as audio recorders, smartphones, tablets, and other devices. It features a 23-foot (7m) cable, which gives you plenty of length to position subjects in front of a camera, around a table for a podcast recording, etc.
Both lavalier microphones have omnidirectional pickup patterns, which is desirable when capturing sound for video and audio recordings, because they don’t reject sound in any direction. This makes for a more even, natural sound quality. The LavMicro M2 features a battery, which means you can use it with a large variety of equipment, and when used with devices like smartphones, the battery is unnecessary and can easily be switched off.
All of the accessories you need to capture excellent audio are included. The alligator-style mic clips provide a firm grasp to collars and clothing. The fitted foam windscreens diffuse unwanted wind noise. An included 1/4” adapter lets you use the LavMicro M2 with cameras like the Blackmagic Design Cinema Camera. The reusable cable ties help you keep your wires tidy. An included miniature screwdriver is provided for accessing the battery, and the compact soft-shell zippered case is exactly what you need for storage and transport.
- 2 high-quality wired lavalier microphones that connect to a single mic input
- Provides broadcast-quality sound DSLRs, mirrorless cameras, audio recorders, smartphones, tablets, and other devices
- A low-cost solution for putting wired clip-on lavalier microphones on 2 people and plugging into a single mic input and achieving excellent sound quality
- The omnidirectional pickup pattern of the mics is ideal for video productions and audio recordings
- 23-foot (7m) cable provides a generous amount of length for creative options, includes compact soft-shell zippered case for storage and transport
Specification:
Type: Condenser MicrophonePolar Pattern: Omni-directional
Frequency Response: 50Hz - 18kHz
Sensitivity: -32 +/-3dB (0dB = 1V/Pa, at 1kHz)
Signal to Noise Ratio: Less than -75dB
Battery Type: One LR44 3V Battery
Weight: 2.5oz (70g)
Cable Length: 19.7’ (6m)
Output: 1/8” (3.5mm) TRS
1-Year Warranty
Saramonic LavMicro Lavalier Microphone for DSLRs, Mirrorless, Video Cameras, Smartphones & more
$ 25.00
Saramonic LavMicro Lavalier Microphone for DSLRs, Mirrorless, Video Cameras, Smartphones & more
MFR SKU: LAVMICRO | Helix SKU: SRLAMICRO
Overview
The Saramonic LavMicro is a wired omnidirectional clip-on lavalier microphone that delivers broadcast-quality sound and can be used with DSLRs, mirrorless and video cameras, as well as audio recorders, smartphones, tablets, and other devices. An included 1/4” adapter even lets you use it with cameras like the Blackmagic Design Cinema Camera. The LavMicro features a 20-foot (6m) cable, which gives you ample room to position your subject in front of the camera.
The LavMicro has an omnidirectional pickup pattern which is desirable when capturing sound for video and audio recordings because it doesn’t reject sound in any direction. This makes for a more even, natural sound quality. The LavMicro features a battery, which means you can use it with a large variety of equipment, and when used with devices like smartphones, the battery is unnecessary and can easily be switched off.
All of the accessories you need to capture excellent audio are included. The alligator-style mic clip provides a firm grasp to collars and clothing. The fitted foam windscreen diffuses unwanted wind noise. The reusable cable wraps help you keep your wires tidy. And an included miniature screwdriver and extra screws are provided for accessing the battery.
- Provides broadcast-quality sound to DSLRs, mirrorless cameras, audio recorders, smartphones, tablets, and other devices
- Includes a wired clip-on lavalier microphone with an omnidirectional pickup pattern that’s ideal for video and audio recordings because it doesn’t reject sound in any direction
- Includes all of the accessories you need to capture excellent audio (clip, windscreen, etc.), 20-foot (6m) cable gives you a generous amount of length for creative options
- Optional battery power makes it compatible with a wide variety of equipment, when used with smartphones the battery is unnecessary and can be switched off
- A low-cost solution for achieving excellent sound quality
Specifications:
Polar Pattern: OmnidirectionalFrequency Range: 50Hz to 18kHz
Signal to Noise: 78 dB SPL
Sensitivity: -32 dB ± 3 dB / 0 dB= 1 V/Pa, 1 kHz
Connector: 1/8" (3.5 mm) TRS/TRRS combo connector
Cable Length: 20' (6.0 m)
Saramonic LavMicro U2 Ultracompact Clip-On Lavalier Microphone for Cameras & Mobile Devices with a 19.7-foot (6m) Cable, Included Battery, Mic Clip, Windscreen & More
$ 89.00 - Sold Out
Saramonic LavMicro U2 Ultracompact Clip-On Lavalier Microphone for Cameras & Mobile Devices with a 19.7-foot (6m) Cable, Included Battery, Mic Clip, Windscreen & More
MFR SKU: LAVMICROU2 | Helix SKU: SRLAVMICROU2
Overview
The Saramonic LavMicro U2 is an ultracompact clip-on lavalier microphone that to captures rich, broadcast-quality sound. It features a 3.5mm TRRS output connector and a dedicated switch that toggles between camera and phone output modes, switching the output to either TRS, or TRRS. Allowing users to plug directly into the mic input on cameras, smartphones, tablets, audio recorders, computers, mixers, and any other device with a 3.5mm input. A 3.5mm to 1/4” adapter is also included to plug into larger input jacks. It has a long 19.7-foot (6m) built-in cable that provides plenty of length to achieve creative techniques, like standing at an optimal distance in front of your device’s camera, sit down interviews in a natural setting, and narrative filmmaking where concealing the microphone is crucial.
Capture great sound with ease
Everything you need to capture perfect sound comes included. A battery comes installed so you can use the LavMicro U2 with cameras and devices that do not provide power to the microphone. The omnidirectional pickup pattern captures sound equally in all directions, so you don’t need to worry about the direction the mic is pointing when you clip it to a shirt. The included alligator-style mic clip holds the LavMicro U2 firmly, and the foam windscreen diffuses unwanted wind noise. A storage pouch with a locking drawstring holds everything neatly.
- Ultracompact clip-on lavalier microphone that plugs directly into cameras, audio recorders, smartphones, tablets, and other devices and delivers rich, broadcast-quality sound
- Built-in 19.7-foot (6m) cable provides an ample amount of length for creative recording techniques like speaking in front of the camera, sit-down interviews and concealing the microphone
- Omnidirectional pickup pattern captures sound equally in every direction, so you don't need to worry about what direction the mic is pointing when clipped to your shirt
- Powered by an included battery, built-in switch to change between phone and camera modes, compatible with 3.5mm and 1/4” inputs
- Includes an alligator-style mic clip that securely affixes to collars and other clothing, a foam windscreen to diffuse wind noise, and a locking drawstring pouch that neatly holds everything
Specifications:
Type: Electret Condenser
Polar Pattern: Omnidirectional
Frequency Range: 65Hz to 18kHz
Sensitivity: -42±3dB (0dB=1V/Pa, at 1KHz)
Signal-to-Noise Ratio: 78dB SPL
Output Impedance: 1000 Ohm or Less
Battery Type: LR626 -AG4
Output Connector: Gold-Plated 1/8“ (3.5mm) TRRS
Cable Length: 19.7’ (6m)
Weight: 1.64 oz (46.5g)
Saramonic LavMicro UC Omnidirectional Lavalier Microphone for USB-C Android Smartphones, Tablets, Computers & more
$ 99.00 - Sold Out
Saramonic LavMicro UC Omnidirectional Lavalier Microphone for USB-C Android Smartphones, Tablets, Computers & more
MFR SKU: LAVMICRO-US | Helix SKU: SRLAMICROUS
Overview
The Saramonic LavMicro UC is an ultra-compact clip-on lavalier microphone that captures pristine sound quality and connects directly to Android devices or PC and Mac computers through the USB Type-C port. This provides a purely digital, low-noise signal transfer that results in rich, broadcast-quality sound, whether you’re shooting video or recording audio with the apps of your choice.
The cable of the LavMicro UC is 6.25 feet (1.9m), which is the ideal length for selfie-stick video, or for neatly tucking your device away in a pocket while you record. A high-quality DeltaSigma analog-to-digital converter is incorporated into the cable. The outstanding audio quality of the LavMicro UC is achieved with the combination of its superior microphone capsule, its high-end analog-to-digital converter, and its digital USB Type-C connector.
The pickup pattern of the LavMicro UC is omnidirectional, which provides smooth and even sound no matter what direction it’s pointing in when clipped to your collar or clothing. Not only do you not need to worry about what direction the mic is pointing in, you also don’t need to worry about batteries. The LavMicro UC provides simple plug-and-play operation with all of your audio recording and video shooting apps.
Specifications:
Polar Pattern: Omnidirectional
Output: USB Type-C
Frequency Response: 30Hz - 20kHz
Sensitivity: -42+/-3DB (1KHz, 0dB=1v/Pa)
Gain: 0-35 dB
Sampling Frequency: 44.1kHz/ 48 kHz
Bitrate: 16Bit / 24Bit – This is not accurate is it 16 Bit/44.1 or 48K or 24 Bit/96K
Power Requirements: Supplied by Device
Transducer Principle: Pre-Polarized Condenser Microphone
Weight: 25g (0.88oz)
Cable Length: 5’ 7” (1700mm)
Product Weight: 0.88oz (25g)
Saramonic LM-WS Furry Windscreen for Saramonic Lavalier Microphones (3-Pack)
$ 10.00 - Sold Out
Saramonic LM-WS Furry Windscreen for Saramonic Lavalier Microphones (3-Pack)
MFR SKU: LM-WS | Helix SKU: SRLMWS
Overview
The LM-WS is a furry windscreen for higher wind conditions, when a foam windscreen just won’t do. Designed for the Saramonic SR-UM10-M1 & SR-UM9-M1 lavaliers that are included with UwMic9, VmicLink5, UwMic10 and UwMic15 wireless systems. It also works with the other Saramonic lavaliers and many other standard-sized lavalier microphones between 6-8mm in diameter. The LM-WS is an ideal solution in high-wind recording environments when lavaliers are worn on the outside of clothing.
- Designed for the SR-UM10-M1 & SR-UM9-M1 Lavaliers (included with UwMic9, VmicLink5, UwMic10 and UwMic15)
- Works with the Saramonic WM4C-M1 (included with SR-WM4C), LavMic, LavMicro, LavMicro DI & LavMicro UC
- Slips Over Lavalier
- Improves Wind Rejection
- Fits Most Standard Lavalier Mics
